Eaton EASY222-DN Скачать руководство пользователя страница 257

Страница: 257 / 284

253

09/10 MN05013007Z-EN

What happens if...?

Module status
LED MS

Possible cause

Remedy

Off

No power at EASY222-DN.

Switch on the power supply.

Green

EASY222-DN is in standby mode.

None

Green flashing

EASY222-DN not configured.

Verify the correct setting of the
MAC ID.

Red flashing

Invalid configuration

Check configuration data.

Red

Module error which can not be resolved.

Replace the EASY222-DN.

Network Status
LED NS

Possible cause

Remedy

Off

• EASY222-DN without power or
• communication is blocked at this

channel because
– of bus-off state or
– power loss or
– the channel was blocked explicitly.

• Switch on the EASY222-DN,
• supply the mains voltage to

the channel and

• ensure that the channel is

active.

Green

Although the channel is enabled, commu-
nication is not possible.

Check the communication
function at the master PLC.

Green flashing

Normal operation

None

Red flashing

Communication error or the EASY222-DN
may be defective.

Reset the module. If further
errors occur, replace the
EASY222-DN.

Red

Communication error.

Check the master PLC.

Содержание EASY222-DN





























































































































































































































































































Результаты поиска

Содержание EASY222-DN

Отзывы:

Похожие инструкции для EASY222-DN

Бренды по названию

Популярные бренды

Eaton EASY222-DN, Руководство пользователя

Результаты поиска

Содержание EASY222-DN

Отзывы:

Похожие инструкции для EASY222-DN

Бренды по названию

Популярные бренды