background image

37

Section IX – Internal Body Passages & Plug Locations 

Two stage directional valves can be converted to different
operational modes, i.e., internal/external, pilot pressure or
drain, fast response, etc. To accomplish this, internal plugs
must be removed or added within the main stage body
passages.

Table 8 is a list of basic models with the incorporated
operational mode changes. Each model is referenced to a
particular figure. The figures illustrate internal passages and
plug locations.

Operational Mode Change

(Reference model code, Table 2)

* - Standard
X - Fast response option
E - External pilot  pressure

CAUTION

DO NOT change internal plugs within main
stage body unless power is off and system
pressure is relieved.

K/R/S - Integral check valve
T

- Internal pilot drain

Basic Model Description

DG5S4-04**-*-40
DG5S4-04**X-*-40
DG5S4-04**-E-*-40
DG5S4-04**X-E-*-40
DG5S4-04**-K/R/S-*-40
DG5S4-04**-E-K/R/S-*-40
DG5S4-04**-X-K/R/S-*-40
DG5S4-04**-X-E-K/R/S-*-40
DG5S4-04**-T-*-40
DG5S4-06**-*-51
DG5S4-06**X-*-51
DG5S4-06**-E-*-51
DG5S4-06**X-E-51
DG5S4-06**-K/R-*-51
DG5S4-06**-E-K/R-*-51
DG5S4-06**X-K/R-*-51
DG5S4-06**X-E-K/R-*-51
DG5S4-06**-T-*-51
DG5S4-H06**-*-51
DG5S4-H06**X-*-51
DG5S4-H06**-E-*-51
DG5S4-H06**X-E-*-51
DG5S4-H06**-K/R/S-*-51
DG5S4-H06**-E-K/R/S-*-51
DG5S4-H06**X-K/R/S-*-51
DG5S4-H06**X-E-K/R/S-*-51

Reference

Table 8. Internal Passages & Plug Tabulation

Figure 23a

Figure 23b

Figure 23c

Figure 24a

Figure 24b

Figure 24c

Figure 25a

Figure 25b

DG5S4-H06**-T-*-51

DG5S4-10**-*-51/53
DG5S4-10**X-*-51/53
DG5S4-10**-E-*-51/53
DG5S4-10**X-E-*-51/53
DG5S4-10**-K/R/S-*-51/53
DG5S4-10**-E-K/R/S-*-51/53
DG5S4-10**X-K/R/S-*-51/53
DG5S4-10**X-E-K/R/S-*-51/53
DG5S4-10**-T-*-51/53
DG5S-(H)8**-*-10/20
DG5S-(H)8**X-*-10/20
DG5S-(H)8**-E-*-10/20
DG5S-(H)8**X-E-*-10/20
DG5S-(H)8**-K/R/S-*-10/20
DG5S-(H)8**-E-K/R/S-*-10/20
DG5S-(H)8**X-K/R/S-*-10/20
DG5S-(H)8**X-E-K/R/S-*-10/20
DG5S-(H)8**-T-10/20
DG5S4-H06*D-51
DG5S-8-*D-*-10
DG5S4-06*D-*-51
DG5S4-10*D-*-51/53

Figure 25c

Figure 26a

Figure 26b

Figure 27a

Figure 27b

Figure 27c

Figure 24a

(Internal plug

locations only)

Figure 26c

Basic Model Description

Reference

Содержание DG17/20V-3 Series














































Отзывы: