Eaton DF6200 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 94

Eaton DF6200 Скачать руководство пользователя страница 11

11

Amended: April 22

EMEA Fire Technical Support: DF6000/CF3000 Applications Guide

Loading and Totals

The general rules are that the panel is capable of supporting up to 200 devices per loop; this can be a
combination of Detection, Callpoints, I/O units, Repeaters and Sounders.
The protocol and internal memory are constructed in such a way that there are certain loading rules
which must be strictly enforced.

Maximum 200 devices per loop
Maximum 60 sounders/beacons/sounder beacons (set low) per loop.
Maximum 20 I/O units per loop which assumes each I/O uses 3 output channels;
Maximum 120 Output channels based on 2 + 3 above.

Certain devices have been constructed to circumvent these rules effectively ‘fooling’ the panel to
offset some of the totals. The maximum 200 per loop CAN NOT be changed.

The totals for EN and UL are the same unless specified in the remarks column.

Device Type

Total per
Loop

Replies as

Remarks

Detectors

200

Optical, Heat or Opto Heat

Call points

200

Callpoint

Sounder/Beacon/Sounder
beacon

60

Sounder Beacon

Individuals all reply the same

MIO/ULCIO (single and 3 chan)

20

3 Chan I/O

MIO324S resets on silence

MCOM/ULMCOM

20

3 Chan I/O

MCOMS/ULMCOMS

60

Sounder Beacon

Uses 1 sounder channel,
ULMCOMS resets on silence

MCOM-FC

60(48)

Sounder/Beacon

Does not respond to EVAC

MCOM - R

20

3 Chan I/O

Not used for UL

MCIM (old version)/ULMCIM

20

3 Chan I/O

MCIM obsolete

MCIM-C/ULMCIM-C

200

Callpoint

MCIM-C obsolete

MCIM - NF

200

Non

– Fire input

Obsolete

MCIM (new version)

200

Input

Not used for UL

Spur Isolator

200

Takes no address

– does

take a load.

EN / UL Zone/Shop unit
Monitors (incl. Mini Module)

20

ZMU/SMU
(Acts as an output device)

Loop loader allows 20
conventional detectors

4 Way Sounder controller

20

SCU

Uses I/O channels

Repeater/Mimic/CIOP/BS7273
Device

200

Repeater

Restricted by load (20) Note
1

Beam Detector

200

Beam Detector

Restricted by load (20) Note
1

4

– 20 mA

20

4

– 20mA

Fan Controller

48 Chan’s Fan Controller

2xFC6

Tech I/O unit

20

I/O and Tech Input

Item takes 2 addresses

Addressable Remote Indicator

60

Sounder Beacon

Gas Interface

N/A

Discontinued

For Australia market

Table 1

Note 1

– The figure in brackets is a recommended total for these devices, there is currently no

restriction placed in the Loop loader program.

Note 2

–

Where total per loop is shown this is a maximum number or a maximum combination with

other output device

«
...
9
10
11
12
13
...
»

Содержание DF6200































































































Отзывы:

Нет отзывов