Eaton APS6-400 Series страница 89 Скачать руководство пользователя

Страница: 89 / 114

Connector Pin-outs

IPN 997-00012-53B December 2010

Connections

The following diagram shows the connections between the SC200 or SC100, the I/O board, the
other dc power system components and external devices.



SC200 or SC100 system controller



I/O board



Voltage feed module



USB communications (SC200 only)



Ethernet communications (SC200 only)



RS232 communications



Digital relay outputs (6) to external devices and/or
alarm indication system



Digital inputs (6) from external voltage-free switches
or relay contacts



Connection to additional I/O board(s) and/or
SiteSure-3G I/O module(s) (SC200 only)



Connection to dc common bus



Connection to dc live bus



Communications to rectifiers



DC power system digital inputs (Load Fuse Fail,
Battery Fuse Fail, AC Distribution Fan Fail, AC
Distribution MOV Fail)



Connections for battery mid-points (4)
(SC200 only)



Connection for temperature sensors (2)



Connection for current sensors (3)



Connection for LVD contactor and auxiliary switch



Connection for LVD contactor and auxiliary switch



Bus voltage sense and LVD power connections



I/O and system controller power and RXP comms
connections



For connector pin-outs see details on page

. For input and output specifications see details on

page

Содержание APS6-400 Series











































































































Результаты поиска

Содержание APS6-400 Series

Отзывы:

Похожие инструкции для APS6-400 Series

Бренды по названию

Популярные бренды

Eaton APS6-400 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание APS6-400 Series

Отзывы:

Похожие инструкции для APS6-400 Series

Бренды по названию

Популярные бренды