background image

Splash Lubricated, Air Compressor Pumps

This manual contains very important information to know and understand. This is provided for SAFETY and to 
PREVENT EQUIPMENT PROBLEMS. To help understand this information, observe the following:

Danger indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.

Warning indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.

Caution indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.

Notice indicates important information, that if not followed, may cause damage to 
equipment.

DANGER

WARNING

CAUTION

NOTICE

Read all manuals included with this product carefully. Be 
thoroughly familiar with the controls and the proper use of the 
equipment.

1.  

Allow only trained, authorized persons who have read and understood these operating instructions to use  

 

this compressor pump. Failure to follow the instructions, procedures and safety precautions in this manual  

 

can result in accidents and injuries.

2.  

NEVER

 start or operate the compressor pump under unsafe conditions. Tag the compressor, disconnect and  

 

lock out all power to it to prevent accidental start-up until the condition is corrected.

3.   Install, use and operate the compressor pump only in full compliance with all pertinent OSHA regulations  
 

and all applicable Federal, State & Local codes, standards and regulations.

4.  

NEVER

 modify the compressor pump and/or controls in any way.

5.   Keep a first aid kit in a convenient place. Seek medical assistance promptly in case of injury. Avoid infection  
 

by caring for any small cuts and burns promptly.

1.  

NEVER

 use air from this compressor pump for breathable air except in full compliance with OSHA Standards  

 

29 CFR 1910 and any other Federal, State or Local codes or regulations.

Death or serious injury can result from inhaling compressed air 
without using proper safety equipment. See OSHA standards on safety 
equipment.

DANGER

Safety Information

Basic Guidelines

Breathable Air

3

Содержание POLAR AIR P01PSXXP10V120V208X











































Отзывы: