Eastwood 13542 Скачать руководство пользователя страница 16

Страница: 16 / 20

Eastwood Technical Assistance: 800.343.9353 >> [email protected]

PROBLEM

CAUSE

CORRECTION

Does Not Run

When Switch

is Turned On

No power to

Buff Motor

Check 120 VAC input plug connection
Check for tripped circuit breaker. The Buff Motor

operates on a 15 Amp Minimum circuit.

Motor Runs

Too Slow/

Develops

Low Power

Excessive volt-

age drop due

to under-sized

and or too long

of an extension

cord used

Extension cords not recommended. If necessary,

use only 14 Gauge or larger cord and limit length

to 25’.

Excessive volt-

age drop due

to local power

company volt-

age supply.

Use at another location or at a time when voltage

is higher.

Excessive

Noise and/or

Vibration

Buff Wheel

likely torn or

damaged.

WARNING:

This is an

extremely

unsafe

condition!

Discontinue use and replace Buff Wheel.

Motor

Overheats

Excessive pres-

sure being ap-

plied to Wheel

while Buffing

Allow Wheel to work by rotation alone. Do Not

Force.

TROUBLESHOOTING

Motor Performance Issues

Содержание 13542





















Результаты поиска

Содержание 13542

Отзывы:

Похожие инструкции для 13542

Бренды по названию

Популярные бренды

Eastwood 13542, Инструкция по эксплуатации

Результаты поиска

Содержание 13542

Отзывы:

Похожие инструкции для 13542

Бренды по названию

Популярные бренды