manualshive.com logo in svg

Eastey TT Series, Руководство пользователя

Поделиться
Скачать
Eastey TT Series Скачать руководство пользователя страница 12

12   Installation 

Installation 

 

Carefully unpack  the outer carton  and shipping material.  Avoid  damaging the 
accumulation table or base. 
 
Remove shipping straps and bolts or brackets securing the accumulation table base to 
the shipping base. Lift the accumulation table base off the shipping base. 
 

CAUTION! 

The accumulation table may require more than one person to 
move safely off the shipping base. 

 

Optional Casters 

 

The accumulation table is delivered with flat leveling feet, standard. If the accumulation 
table is ordered with optional locking casters, the casters are installed at the factory and 
the accumulation table is delivered with the casters installed. 
 

 

Height Adjustment 

 

Each leg of the accumulation table  is a threaded leveling leg.  (Thread-locking 
compound is used to secure the feet or optional casters to the leveling leg.) To adjust 
the leg height, twist to thread the leg into or out of the accumulation table base to adjust 
each leg up or down. 
 

 

 
Move the accumulation table to the desired location. The leveling foot may require some 
lifting, but will easily skid across a smooth, level floor surface. If you have purchased the 
optional locking casters you can roll  the  accumulator  table  easily over a smooth flat 
surface. Move  each caster  lever to the locked position to keep the accumulation table 
from moving. 
 
 
 

 

Lower

Raise

Lower

Raise

Содержание TT Series



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды