Eastey SB-2 EX-Auto Скачать руководство пользователя страница 55

Страница: 55 / 59

Warranty Statement 55

Warranty Statement

SB-2/3EX-Automatic Carton Sealing Machine

Warranty Statement

Eastey warrants that all of the products it ships will be in good working order and free

from defects in material and workmanship and will conform to the published

specifications for that product.

Warranty Period

Drive motor(s): 1 year

Gear reducer: 1 year

Tapehead:

1 year (Except for moving parts which are subject to normal

wear, tear and replacement which are warranted to be free from

defects in material and workmanship.)

All other parts: 1 year (Except for moving parts which are subject to normal

wear, tear and replacement which are warranted to be free from

defects in material and workmanship.)

Taping Quality

Taping quality achieved in a given application is dependent on the installation, the

material handling, and the maintenance provided. Eastey makes no warranty that the

print quality achieved in an application will be the same as that achieved on a test piece

in our laboratory.

Shipping Policy

Customer pays all incoming shipping. If the item is defective and under warranty,

Eastey pays return shipping charges for least costly method. If expedited shipping is

desired, customer must furnish his shipping account and shipping fees will be charged

to that account.

Warranty Verification

If you conclude that a product may be defective and may be covered by warranty,

obtain a Return Material Authorization number by calling our technical support number

(toll free at 1-800-835-9344, or 763-428-4846 or Fax 763-795-8867 or e-mail

[email protected]). Once an RMA number has been obtained, return the defective item

to Eastey. Eastey will analyze the product and, if found to be defective, we will, at our

option, replace or repair the item. If the item is found to not be eligible for warranty, you

will be notified and may decide on disposition. Defective products will be replaced or

repaired as promptly as possible.

Warranty Eligibility

The warranty provided by Eastey is only to the original buyer.

Содержание SB-2 EX-Auto




























































Результаты поиска

Содержание SB-2 EX-Auto

Отзывы:

Похожие инструкции для SB-2 EX-Auto

Бренды по названию

Популярные бренды

Eastey SB-2 EX-Auto, Руководство пользователя

Результаты поиска

Содержание SB-2 EX-Auto

Отзывы:

Похожие инструкции для SB-2 EX-Auto

Бренды по названию

Популярные бренды