manualshive.com logo in svg

EarthLinked TXV Kit, Руководство по установке

Поделиться
Скачать
EarthLinked TXV Kit Скачать руководство пользователя страница 2

 

TXV-CLP-KIT (07/15) 

 

 

Model Nomenclature 

 

 

 

 

 

 

 

Disclaimer 

Proper installation and service of EarthLinked

®

 Heating and Cooling System Components is 

essential to reliable performance. All EarthLinked

®

 components must be installed and serviced by a 

technician authorized by Earthlinked Technologies. Installation and service must be made in 
accordance with the instructions set forth in this manual.  Failure to provide installation and service 
by an authorized installer consistent with this manual will void the limited warranty coverage for the 
system. 

EarthLinked

® 

Technologies shall not be liable for any defect, unsatisfactory performance, damage 

or loss, whether direct or consequential, relative to the design, manufacture, construction, 
application or installation of the field specified components.  

 

 
 
 
 
 
 
 
 

Earthlinked Technologies, Inc. 

4151 South Pipkin Road 

Lakeland, Florida 33811 

tel. 863-701-

0096 ● fax 863-701-7796 

info@earthlinked

.com ● 

www.earthlinked.com

 

CSI # 23 80 00 

Содержание TXV Kit





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды