E
B
F
F
F
F
E
E
E
E
Mount Laurel,NJ 08054 USA
www.ecr4kids.com
Model No. ELR-0636
25-Tray Storage Cabinet
TIP
！
DO NOT FULLY
TIGHTEN SCREWS
UNTIL ALL SCREWS
HAVE BEEN LOOSELY
POSITIONED
。
!
WARNING:
-
Adult Assembly Required.
Two
adults recommended.
- Contains small parts, sharp points
and edges.
- Do not stand, sit, kneel, climb, lean
or pull on unit for support.
- Never leave children unattended.
- Do not place unit near high heat or
moisture.
- Adult Supervision Recommended.
Left Side Panel
Right Side Panel
Top Shelf
Middle Shelf(1)
Middle Shelf(3)
Bottom Shelf
Back Panel(5)
Divider(4)
Large Hex Screw(20)
Metal Dowels(8)
Hex Key Tool
Wheel Casters(4)
Caster Screws(16)
Cams(8)
PARTS LIST
B
D
E
F
C2
A1
A2
C1
G
H
I
J
K
L
B
B
C2
D
E
F
C2
C2
C1
A1
F
F
F
D
A2
A1
A2
BEFORE ASSEMBLING,
MAKE SURE THERE
ARE NO
MISSING PARTS.
B
H
Ｘ８
H
1
Attach the Dividers to the Top Shelf
B
F
F
F
F
L
Ｘ８
L
1A. Place the Top Shelf(B) top-down on a carpet or protected surface.
Insert 8 Metal Dowels(H) into the plastic plugs located underneath
the Top Shelf(B). Tighten with a Phillips Head Screwdriver.
1B. Insert 2 Cams(L) into the large holes in each of the Dividers(F).
Make sure the arrows on Cams(L) point toward the holes in the closest
edge.
1C. Position the Dividers(F) so Metal Dowels(H) attached to Top Panel(B)
enter the holes in the top edge. Turn Cams(L) with a Phillips Screwdriver
until locked onto the Metal Dowels(H).
2
Insert the Back Panels
2. Slide the Back Panels(E) into the grooves between the Dividers(F)
until fully inserted into the slot as shown.
B
E F
C2
C2
C2
C1
3
Insert the Middle Shelves
3A. Insert a Middle
Shelf(C2) as shown
onto the Dividers(F)
until fully inserted.
3B. Insert a Middle
Shelf(C1) as shown
onto the Dividers(F)
at the center slots
until fully inserted.
3C. Insert 2 Middle
Shelves(C2) onto the
Dividers(F) as shown
until fully inserted.
4
Attach the Divider Section to
the Base
4. Attach the Base
to the Divider
Section(F,E,C1,C2)
using 8 Large Hex
Screws(G). Tighten
with the Hex Key
Tool(I).
5
Attach the Wheel Casters
5. Beginning with the holes on the inside of the Wheel Caster(J) mount
plate (opposite the kickplate on Base(D)), attach the 4 Wheel Casters(J)
using 16 Caster Screws(K). Tighten with a Phillips Screwdriver.
G
Ｘ８
G
D
B
E
F
F
F
F
C2
C2
C2
C1
B
D
F
C2
C2
C2
C1
J
K
Ｘ４
Ｘ１６
Version: ELR-0636.D.2010.01.03
J
K
Attach
First
Mount
Plate
Caster
Screw