GND
+5V
Vout
Vin
TX2
Package includes
Flight controller connection diagram
Eachine UZ65 1
-
2S Brushless whoop Flysky version
Binding procedure
1.Plug the USB and then go to the CLI command tab of the betaflight configurator, then type
"bind_rx" from the command line. The red LED on the flight controller will blinking fast ,this
indicate the receiver is in bind mode .
Specifications
Brand Name: Eachine
Item Name: Uz65 65mm FPV Racing Drone
Wheelbase: 65mm
Size: 80mm*80mm*40mm
Weight(without battery): 21g
Weight(with battery): 29g
Receiver option:
Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode)
Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter)
External DSM2/DSMX Receiver version(Compatible with Spektrum DX6I/DX7/DX8/DX9)
External TBS Crossfire Nano RX version(Compatible with TBS transmitter)
Features
The smallest 1-2s 3 in 1 flight controller built-in ESC, Receiver
The world first 65mm whoop with 35mm propellers
Runcam Nano3 The lightest 1/3 CMOS 800TVL Camera
Smooth and powerful
Compatible for 1S Lipo/LIHV
Camera Angle adjustable
Qty
1
1
4
1
1
1
4
1
1
1
Item Name
UZ65 1S 65mm whoop Drone Frame
SPI Receiver Option1: Superbee F4 FC built-in Frsky SPI D8 RX
SPI Receiver Option2: Superbee F4 FC built-in Flysky SPI RX
External Receiver Option3: Superbee F4 FC with DSM2/DSMX RX
External Receiver Option4: Superbee F4 FC with TBS crossfire RX
NC0802 KV19000 brushless motor
HQPROP 35mm-3 blades Propellers(4cw+4ccw)
Runcam Nano3 1/3 CMOS 800TVL camera
5.8G 25mw-100mw 40ch vtx
1S 300mah 30C LiHV Battery
1S Lipo/LIHV USB Charger
Propeller disassemble tool
Eachine Handbag
Red
LED
status
Meanings
Solid--Normal
working
or
bind
successful
Blinking
slowly--No
signal
Blinking Fast--Bind mode
M4_C
M4_B
M4_A
M3_A
M3_B
M3_C
GND
M1_A
M1_B
M1_C
M2_A
M2_B
M2_C
TX1
RX2
Vout
Vin
+5V
GND
BUZ-
IR1
LED_strip
GND
+5V
RX1
TX2
Arm/Disarm the Motor
Receiver configuration
Please set Receiver mode to be SPI RX Support from the Configuration tab of the Betaflight
Configurator, then select A7105_Flysky_2A Provider for AFHDS-2A Protocol Radio transmitter
or Select A7105_Flysky Provider for AFHDS Protocol Radio transmitter, don't enable Serial RX
since the Superbee F4FS flight controller is integrated SPI BUS Receiver
3.The default channel map for UZ65 Flysky version is AETR1234, please make sure your
transmitter is matched, otherwise it will can't be armed. Toggle the AUX1 Switch ,the Green
LED on the flight controller will getting to be solid, this indicates the motor was armed . And
also you can found “Armed” displayed on your FPV Goggles or the FPV Monitor. Please make
sure keep the
level before arming .Be careful and enjoy your flight now !
UZ65
2. Set Arm/Disarm switch for your Flysky Radio: Move to the Aux.channels interface, Set
“SWA” or “SWB” or “SWC” switch etc. for Ch5 to ARM/DISARM the motor.
1. The Default Arm/Disarm switch for UZ65 is AUX1(Channel 5),and you can also customize it with
Betaflight Configurator.
2.Turn on your Flysky transmitter, and Choose receiver mode AFHDS-2A or AFHDS according to
your Betaflight receiver configuration(
A7105_Flysky_2A=AFHDS-2A
,
A7105_Flysky=AFHDS
)
3.ENT RX [BIND] to binding with the Superbee F4FS flight controller, The red LED on the flight
controller
will getting to be solid on the flight controller ,this indicate binding successfully, the
AFHDS-2A radio will auto exist the binding mode but the AFHDS radio should exist binding mode
by yourself.
