E2S Warning Signals
Impress House, Mansell Road, Acton, London W3 7QH [email protected] e2s.com Page 1 of 3 D242-00-511-IS_Issue_1 - 26/04/2021
INSTRUCTION & SERVICE MANUAL
SONFL1X-HO Range - High Output Alarm Horn & Xenon Strobe Beacon
+ve IN
-ve IN
+
+
-
-
Stage 2
S2
-
+
-
+
DC
Dimensions: 172 x 86 x 83mm
Cable Entry: 2-off M20 x 1.5mm
Temp: -40°C to +55°C
Unit weight: 0.46Kg
Model No.
Nominal Voltage
Voltage Range
Horn Nom.
Current
Beacon Nom.
Current
Sound Pressure Level dB(A)
Max
Nominal
SONFL1XDC012…[X]/[Y]-H
12V dc
10-14V dc
50mA
500mA
105.0 @ 1m
96.0 @ 3m
103.0 @ 1m
94.0 @ 3m
SONFL1XDC024…[X]/[Y]-H
24V dc
20-28V dc
80mA*
250mA
*Current at nominal voltage on Tone 2
[X] Denotes Housing Colour: R = Red; G = Grey; W = White
[Y] Denotes Lens Colour: A = Amber; B = Blue; C = Clear; G = Green; M = Magenta; R = Red; Y = Yellow
Note: CPR Approved Units only available with Clear Lens
SONFL1X-HO Combined Sounder & Xenon Beacon
10 Selectable Tones & 2 Stages
5J Xenon Flash Tube
Three Modes: Flashing 1Hz (AC & DC)
Flashing 1.5Hz and Double Strike (DC Units Only)
1Hz Flashing mode CPR / VdS approved
24Vdc version CPR / VdS approved
CE, EAC Approved
IP Rating: IP66
Use suitable conduit or cable glands with
suitable IP or type rating
0.4Nm
5
0.5 - 1.5mm²
Terminal Connections
SONFL1X-HO
Attention: Installation must be carried out by an electrician in compliance with the latest codes and regulations.
Attention: L'installation doit être effectuée par un électricien conformément aux derniers codes et réglementations.
Achtung: Die Installation muss von einem Elektriker gemäß den neuesten Vorschriften und Bestimmungen durchgeführt werden.
Attenzione: L'installazione deve essere eseguita da un elettricista in conformità con i codici e le normative più recenti.
Atención: La instalación debe ser realizada por un electricista de acuerdo con los últimos códigos y regulaciones.
Atenção: A instalação deve ser realizada por um eletricista de acordo com os códigos e regulamentos mais recentes.
Внимание: установка должна выполняться электриком в соответствии с последними нормами и правилами.
Attention: Disconnect from power source before installation or service to prevent electric shock
Attention: Débranchez-le de la source d'alimentation avant l'installation ou l'entretien pour éviter tout choc électrique.
Achtung: Vor Installation oder Wartung von der Stromquelle trennen, um einen Stromschlag zu vermeiden.
Attenzione: scollegare dall'alimentazione prima dell'installazione o dell'assistenza per evitare scosse elettriche.
Atención: desconéctelo de la fuente de alimentación antes de la instalación o el servicio para evitar descargas eléctricas.
Atenção: Desconecte da fonte de alimentação antes da instalação ou serviço para evitar choque elétrico
Внимание: отключите от источника питания перед установкой или обслуживанием, чтобы предотвратить поражение
электрическим током.
No liability is accepted for any consequences of the use of this document. The technical specifica on of this unit is subject to change without no ce due to our policy of con nual
product development. All dimensions/weights are approximate. This unit is sold subject to our standard condi ons of sale, a copy of which is available on request.
DC Circuit
See D242-06-501 - Schematic Wiring
S2
SWITCH
+
-
Volume
Control
Tone Selection
(See Table)
S2 Denotes Stage 2
customer supplied
Stage switches are
BEACON
PCBA
+
-
Stage 1: Apply Power to +ve & -ve
Stage 2: Apply Power to +ve & -ve & connect Stage 2 to -ve
Beacon pre-wired to Alarm terminals by default
Note: Stage 2 is not VdS Approved
