E.F. Johnson Company 5300 ES Series Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 142

background image

3-4

5300 ES Series Mobile Radio Operating Manual

General Operation

3.4.1

Zone / Channel Display

The selected zone and channel numbers are displayed by the zone and channel displays
shown in the following illustration. In addition, the selected zone identification (alias) is
displayed in the alphanumeric display area when the zone select mode is enabled, and the
channel alias is displayed when the channel select mode is enabled (see following).
Channel alias can be a combination of zone and channel aliases. With conventional
channels, the channel frequency may be displayed instead of the alias if the Display
Information option switch is programmed (see Section 5.8).

A zone can include any mix of up to 16 channels, and up to 32 or 54 zones can be
programmed, depending on the option enabled. Therefore, up to 864 channels can be
selected. One use for zones may be for operation in different geographical areas.

3.4.2

Zone / Channel Select

The front panel Select switch is used to change the zone and channel. Pressing this switch
toggles between the zone and channel select modes, and rotating it changes the zone or
channel.

The current mode is indicated by the bar over the zone or channel display. For example,
when the bar is over the zone display (see following illustration), the zone select mode is
enabled.

Rotating the Select switch clockwise increases the zone or channel and rotating it
counterclockwise decreases the zone or channel number. After the highest zone or channel
is displayed, wrap-around to the lowest zone or channel occurs and vice versa. If an
unprogrammed channel is selected, “UNPROGRAMD” is displayed and a tone sounds.
The radio may also be programmed so that only programmed channels are selected.

The radio can be programmed so that the bar defaults to either the zone or channel display
when power is turned ON and after a change is made. The delay that occurs before it
returns is programmed for 1-255 seconds. It can also be programmed to remain in the last
selected mode.

Zone

Number

Channel

Number

Zone Select Indicator

Channel Select Indicator

«
...
28
29
30
31
32
...
»

Содержание 5300 ES Series















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5300 ES Series

Бренд: Rapid Страницы: 2

Бренд: Baofeng Страницы: 7

FM RDS/DAB Digital Radio RD-50CFM

Бренд: Roberts Страницы: 20

Бренд: Legacy Страницы: 24

Бренд: Racal Instruments Страницы: 102

Бренд: TYT Страницы: 39

Бренд: Hyundai Страницы: 24

Бренд: Sangean Страницы: 41

Бренд: GME Страницы: 36

Бренд: Simoco Страницы: 2

Бренд: Sun-Mate Страницы: 14

Бренд: Grundig Страницы: 30

Бренд: Retekess Страницы: 14

Бренд: Curtis Страницы: 8

Бренд: Intek Страницы: 32

Бренд: Intek Страницы: 44

DESPICABLE ME MINION MADE MINION MANIA

Бренд: KIDdesigns Страницы: 2

X-Tra Talk GXT1000 Series

Бренд: Midland Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды