E.F. Johnson Company 5300 ES Series Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 142

background image

5300 ES Series Mobile Radio Operating Manual

9-3

Password Description

9.2.3

Master Password

The Master Password overrides all the preceding passwords. It can be used by a system
administrator as a “pass key” to a password controlled function or to change a lost or
inadvertently changed password. Master passwords are set up and changed the same as the
other passwords. It does not override the following Zone Password.

9.3

Zone Password

A zone password can be programmed with the 5300 ES mobile radio. It prevents
unauthorized reprogramming of zones by keypad programming.

Note

The programming and usage of this password has not changed. It is independent from the
preceding passwords, and programmed using PC Configure.

«
...
113
114
115
116
117
...
»

Содержание 5300 ES Series















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5300 ES Series

Бренд: Dataradio Страницы: 31

HD Radio NS-HDRAD

Бренд: Insignia Страницы: 17

E TRAVELLER VII

Бренд: Grundig Страницы: 9

Бренд: Mimomax Страницы: 56

Бренд: Raymarine Страницы: 2

Бренд: Baofeng Страницы: 25

Бренд: Hama Страницы: 150

WaveGuide 5 Direction

Бренд: RADAC Страницы: 35

Бренд: Ericsson Страницы: 32

GT-5R EU Series

Бренд: Baofeng Страницы: 120

Бренд: Kongsberg Страницы: 56

Бренд: Motorola Страницы: 46

ASTRO XTSTM 2500 II

Бренд: Motorola Страницы: 24

Бренд: Motorola Страницы: 46

Бренд: Motorola Страницы: 68

Бренд: Motorola Страницы: 86

Commercial Series

Бренд: Motorola Страницы: 100

Бренд: Motorola Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды