manualshive.com logo in svg

E+E Elektronik EE772, Руководство пользователя

Поделиться
Скачать
E+E Elektronik EE772 Скачать руководство пользователя страница 23

23

2. 

Installation

In order to set up a smooth installation of the configuration software of the EE772, admin authorization for the 

personal computer is required. 

• 

During installation of the software the EE772 should NOT be connected with the USB cable to the 

computer.

• 

Wit Setup.exe the InstallShield-Wizard for the EE772 configurator will be started.

• 

Follow the instructions on the screen to install the software.

At first, the configuration software will be installed and then the installation of the USB driver activated – except 

if the user has defined that USB setup is disabled.

The USB driver will be automatically installed the moment the first connection is made with the EE772.

The appearing dialog boxes can be dealt with the settings “No. do not download driver from the internet” and 

“Install the hardware automatically”.

If the EE772 configuration software and the USB driver are installed correctly, and the EE772 is connected 

via the USB interface with the personal computer, a connection “Silicon Labs CP210x USB to UART Bridge” 

should have been created in the device manager. 

See: Start => Settings => Control Panel => System => Hardware =>  

Device Manager

2.1.  Configuration of the USB Interface (VirtualCOM)

After the startup of the software, the correct VirtualCOM interface for the  

USB driver must be configured

The number for the used USB interface can be found under: 

 

Start => Settings => Control Panel => System => Hardware =>  

Device Manager

The setting is done under menu “Extras” and menu item “Optional extras…..”

Содержание EE772

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды