background image

Document:  

Date

Created By: 

 

ECO# 

LPN00684X0001A0_A 

  3-9-2020

TMT 

  011592

INSTALLATION INSTRUCTIONS

E-WPS Series

www.e-conolight.com      |     888.243.9445     |     FAX: 262.504.5409

CAUTION:

 Changes or modifications not expressly approved could void 

your authority to use this equipment. 

This device complies with part 15 of the FCC Rules. Operation is subject 
to the following two conditions: (1) This device may not cause harmful 
interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits 
for a Class A digital device, pursuant to part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against 
harmful interference when the equipment is operated in a commercial 
environment. This equipment generates, uses, and can radiate radio 
frequency energy and, if not installed and used in accordance with 
the instruction manual, may cause harmful interference to radio 
communications. Operation of this equipment in a residential area 
is likely to cause harmful interference in which case the user will be 
required to correct the interference at his own expense.
CAN ICES-005 (A)/NMB-005 (A)

FCC NOTICE

Fixture is equipped with universal volt driver 120-277V 
(ie. 120V, 208V, 240V or 277V)

PHASE TO NEUTRAL WIRING 120/277V

1.  Connect supply ground to fixture ground (green) lead.

2.  Connect supply common to fixture neutral (white) lead.

3.  Connect supply Vin to fixture hot (black) lead.

Tuck all wires carefully into wiring chamber ensuring that no wires 
are pinched.

PHASE TO PHASE WIRING 208/240V

1.  Connect supply ground to fixture ground (green) lead.

2.  Connect supply L1 (Hot) to fixture neutral (white) lead.

3.  Connect supply L2 (Hot) to fixture hot (black) lead.

Tuck all wires carefully into wiring chamber ensuring that no wires 

are pinched.

FIXTURE WIRING

Содержание Savr E-WPS Series










Отзывы: