DT1120-TN20
OWNER’S MANUAL
Thank you for purchasing
the
DynaTrap
®
Insect Trap!
This product may be covered by one or more U.S. patents
or pending patent applications. See www.DynaTrap.com/patents
A0
01
-3
18
.2
01
9.3
HOW THE DYNATRAP
®
INSECT TRAP WORKS
Flying insects are attracted to the unit by UV light and CO2
that is generated by the photo-catalysis between the UV-LIGHT
LED lamp and special TiO2 coating. The fan then pulls the
insects into the screened base, trapping them until they
dehydrate and die. The base can be removed, allowing the
contents to be periodically emptied into the trash.
IMPORTANT: READ CAREFULLY
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
WARNING:
when using electric appliances, basic precautions should
always be followed, including the following:
1. Please read all instructions before using the DynaTrap
®
Insect Trap and keep for future reference.
2. To disconnect, twist housing to the ‘OFF’ position, then remove plug from outlet.
3. To reduce the risk of injury from moving parts or electric shock, always turn unit off and disconnect plug when
not in use and before servicing or cleaning.
4. Always unplug before replacing lamp. Replace with same type rated UV-LIGHT LED 2.4-Watt bulbs,
DynaTrap
®
model 41020.
5. Do not position the unit near heat, gas, oil or other flammable materials.
6. Place out of reach from children.
7. To reduce the risk of electrical shock, do not put appliance in water or other liquid.
8. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been
dropped or damaged, or if it has been dropped into water or other liquid.
9. Connect only to a circuit that is protected by a ground-fault circuit-interrupter (GFCI).
10. Do not insert fingers or any foreign objects into the unit while it is connected to an electrical outlet.
11. Collected insects within the unit may contribute to fire, so clean insects from the unit frequently.
12. Do not clean this product with water spray. Do not place where it can fall into water, or near flammable materials.
13. Do not touch fan while in motion.
14. Do not abuse cord—never carry or hang unit by cord or yank it to disconnect from receptacle.
Keep cord away from sharp edges.
15. If using outdoors, use only extension cords with a tag stating, “Suitable for Use with Outdoor Appliances.”
16. Use only extension cords that have plug and receptacles that match the product plug. Replace or repair damaged cords.
17. Only use attachments recommended or sold by the manufacturer.
18. This appliance is provided with double insulation. Use only identical replacement parts.
See instructions for Servicing Double-Insulated Appliances.
INSTALLATION & OPERATING INSTRUCTIONS
1. Unpack unit. Save carton for off-season storage (if needed).
2. If hanging or mounting the trap place approximately 3–6 feet above the floor/ground level for optimal catch
rate and easy access for cleaning.
3. If mounting the trap to a wall, secure the mounting bracket to a wall, fence, or other stationary surface using the
mounting hardware (included). Then, mount the trap on the bracket by sliding the mounting channel on the side
wall of the trap over the mounting bracket peg.
Problem:
Possible cause:
Correction:
Bulb does not illuminate
and fan does not spin.
No electrical power.
1. Check plug, receptacle and fuse or circuit breaker.
2. Check to make sure power is switched to the “ON” position.
Bulb illuminates, but fan
does not spin.
Shorted fan.
UNPLUG UNIT: Examine fan to see that it is free from
foreign material, dirt or build-up of dead insects.
Clean unit as in “CLEANING” section.
Fan spins, but bulb does
not illuminate.
1. Bulb not seated
properly
2. Burnt out bulb
The UV-LIGHT LED has an expected lifespan of 20,000 hours.
If lamp fails to illuminate before 20,000 hours of operation,
call customer service at 877-403-8727.
TROUBLESHOOTING
LIMITED WARRANTY
DYNAMIC guarantees to the original purchaser that this product is free from defective materials and workmanship. This warranty is
limited to remedy any defective part for a period of one year from date of original date of purchase. Retain your original receipt
as proof of purchase. This warranty does not apply to the light bulb, nor to, in our judgment, misuse or abuse. If this unit has been
altered, no warranty is in force. This warranty does not apply if this unit is purchased outside the United States, excluding Canada
and Mexico. In no case shall DYNAMIC be liable for any accidental, punitive, consequential, or any other damages of any kind for
breach of this or any other warranty, expressed or implied, whatsoever. Some states do not allow limitation on how long an implied
warranty lasts, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may
also have other rights that vary from state to state.
REPLACEMENT PARTS
41020
2.4-Watt Replacement UV-LIGHT LED Bulb (1 piece)
To see all replacement and accessory parts available for your DynaTrap, visit www.DynaTrap.com.
FOR HOUSEHOLD AND COMMERCIAL, INDOOR AND OUTDOOR USE
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
A
B
C
This device complies with Performance Standards
for Light-Emitting Products, 21 CFR, Part 1040,
Chapter 1, Subchapter J, Radiological health.
4002907
Dynamic Solutions Worldwide, LLC
U.S.A. & Canada
12247 W. Fairview Ave. Milwaukee, WI 53226
1-877-403-TRAP (8727)
[email protected] | www.DynaTrap.com
Mexico
Dynatrap Servicios de Mexico S. de R. L. de C.V.
01-800-880-8727 | [email protected]
©2019 Dynamic Solutions Worldwide, LLC
4. For best catch results leave unit on at all times, except when cleaning or servicing.
5. Catch rate activity will be higher at night. For best catch results it is recommended to keep the unit away from
competing light sources.
6. It is recommended to place the unit at least 20 to 40 feet away from where people will be sitting.
7. This unit is all-weather resistant - designed for outdoor use including rainy conditions.
Intended for household and commercial, indoor and outdoor use.
8. To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other).
This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
9. SERVICING OF DOUBLE-INSULATED APPLIANCES - In a double-insulated appliance, two systems of insulation are
provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a
means for grounding be added to the appliance. Servicing of a double-insulated appliance requires extreme care
and knowledge of the system and should be done only by qualified service personnel. Replacement parts for a
double-insulated appliance must be identical to those parts in the appliance. The symbol must be identical to those
parts in the appliance. A double-insulated appliance is marked with the words “DOUBLE INSULATION”,
“DOUBLE-INSULATED” or the symbol:
USER MAINTENANCE INSTRUCTIONS - CLEANING
Clean the trap at least once a week to prolong life of the unit, insure fire prevention, and provide for more efficient
operation.
1. Be sure to clean the unit once per week.
2. Unplug before cleaning.
3. For weekly cleaning, twist the cage clockwise, and remove the damper by grasping the crossbar near the edge of
the damper. Pull up firmly. Remove any buildup from the inside of the retaining cage and fan with a brush
(included). Replace damper, snap firmly into place.
4. For major cleaning, remove the screws securing the fan housing to the light housing. After removing the screws,
gently pull the fan housing away from the light housing. Using a soft brush, remove dirt and debris from the light
housing. Once the cleaning process has been completed, align the screw holes in the fan housing with the screw
holes in the lighting unit and tighten the screws to the base of the lighting unit.
5. When replacing the retaining cage – DO NOT press / push against the screen windows.
REPLACING BULB
Replace With DynaTrap UV-LIGHT LED Bulb #41020 (or equivalent G24 Type - 120V/2.4W UVA Bulb)
The UV-LIGHT LED light bulb life expectancy is approximately 20,000 hours (or about 2.25 years).
1. UNPLUG UNIT, and allow bulb to cool before replacing.
2. Remove screw (A). Twist cover counter-clockwise (B). Tilt cover back to expose bulb (C). Note: Upper and lower
sections will remain connected by electrical wire - Do Not Pull or Attempt To Disconnect.
3. Untighten the screw securing the base of the light bulb to the light housing. Cover the bulb with a cloth to protect
your finger and hand. Grasp the bulb (with your hand and fingers protected by the cloth) and gently pull the
bulb from the socket.
4. Remove any debris from the lamp socket with a brush before inserting the new bulb.
Replace the metal clip over the base of the bulb and tighten the retaining screw.
5. Replace cover onto grill and twist clockwise to lock, replace screw and tighten to secure.
