Power adjustment
nut
Door
Frame
Door
Leaf
B
A
B
A
(19)
3/4
(76)
3
9-1/16
(230)
L
s
B
P.A Plate
Left hand door illustrated.
Same dimensions apply to
right hand door.
Measured from hinge Center.
Dimensions are in inches
(mm)
Not To Scale
mm
Inch
9-1/4
7-3/4
Dimension"A"
Opening Angle
235
197
TO 100°
*OVER 131°
105
156
4-1/8
6-1/8
Dimension"B"
Inch
mm
Pinion flat
For left hand door
Pinion flat
For right hand door
INSTALLATION STEPS:
1. Select degree of opening and use dimensions shown or attached template to locate 4 holes on
door for closer body and 4 holes
underside of frame for P.A plate.
2. Prepare door and frame for fasteners. See
"Preparation for Fasteners", Figure 1
, Page 1.
3. Before installing closer body, set spring power for closer using Power adjustment chart, Page 1.
4. Disassemble forearm from main arm by removing elbow washer and screw.
Remove the foot from the forearm and discard.
5. Attach closer to door with
Power adjustment nut toward hinge
.
6. Attach P.A plate to top frame as shown.
7. Use adjustable wrench to rotate the bottom s pindle by 45° toward the hinge edge .
Hold it and Place main arm on top spindle so that the " B' (Right hand door) or ' A" (Left hand door) lines up with
spindle flat . Secure main arm and spindle by tightening spindle bolt.
8. Fasten forearm to P.A plate using screw included in screw pack.
9. When the door is closed, adjust forearm length to set arm elbow about 1-1/2"(38mm) from door when
connected to main arm. Use washer and screw provided to secure pivot connection. Tighten locknut.
10. Snap the pinion cap over spindle at the bottom of closer.
11. Adjust closer. (See Page 2)
H
ing
e
Speed Regulating
Valves
4
！
Caution
s
s
5-3/4
146
7-5/8
194
*101° TO 131°
Installation Selection:
DYN-1614,DYN-1636 DOOR CLOSER
Installation Instructions
Grade 1, Meets ANSI A156.4
Top Jamb(Push Side)
See Page 3.
Parallel Arm(Push Side)
See Page 4.
How to tell the hand of a door.
1
Regular Arm(Pull Side)
See Page 2.
Pull side
Hinge side of door
Stop side of door
Stop side of door
Push side
This is a left hand door
This is a right hand door
Latch
10°
Caution:
Do not back valves out of
closer or a leak will result.
Closed
Sw
eep
Standard closing cycle
ATTENTION:
Adjust closing time between
4 to 6 seconds from 90°.
USE of the door by
handcapped,elderly or small
children may require longer
closing time.
Closed
O
pe
nin
g
Backcheck
ATTENTION:
Backcheck(BC) valve controls the
hydraulic resistance to door opening in
backcheck range. NEVER close this
valve completely.
It is not to provide a positive stop.
Door opening control
Caution:
Do not back valves out of
closer or a leak will result.
PARALLEL ARM (PUSH SIDE)
Improper installation may result in personal injury or property damage.
Follow all instructions carefully please.
Hinge side of door
Door closing control
5/16
(8) 7/16
(11)
2
(51)
2-3/4
(70)
A
s
A
B
1-1/2
(38)
Door
Frame
Door Leaf
3/8
(9.5)
* Recommended mounting for meeting ADA compliance
* When door closer is installed and adjusted to conform to ADA
reduced opening force requirements (5 lbs max.), it may not have
adequate closing force to reliably close and latch the door.
TOOLS REQUIRED
METAL
#7
1/4"-20
WOOD
3/16"
*Pilot Hole Required
Self Drilling /Tapping
screws
Wood and Metal
For wood, drill 3/16" hole
Machine Screws
#7 Drill, 1/4"-20 Tap
Sleeve Nut and Bolt
Drill 9/32" thru from
Closer side
3/8" Drill other Side
Check building and fire
codes to see if your
application requires the
use of sleeve nuts and
bolts.
Preparation for Fasteners-Figure 1.
Components
Elbow washer
& Screw
Arm Screw
Main Arm
Pinion Cap
Foot
Rod
Lock
Nut
Closer Body
P.A Plate
Screw Pack
Plastic cover
(Optional)
Power 1 to 4 setting & door width
Regular & Top Jamb Installation
Parallel Arm Installation
Maximum Size of Door Width (Factory Preset as size 3)
Size
1
2
Interior
Exterior
Inswing
Exterior
Outswing
Size
Interior Exterior
Outswing
28''
36''
42''
48''
36''
30''
36''
42''
42''
36''
30''
36''
30''
1
2
3
4
3
4
0 Turns
6 Turns
C.W
8 Turns
C.C.W
Full 360°
Turns
5 Turns
C.C.W
C.W-Clockwise
C.C.W-Counter-Clockwise
Power 3 to 6 setting & door width
Regular & Top Jamb Installation
Parallel Arm Installation
Maximum Size of Door Width (Factory Preset as size 4)
Size
Interior
Exterior
Inswing
Exterior
Outswing
Size
Interior Exterior
Outswing
4 Turns
7 Turns
C.W
7 Turns
C.C.W
Full 360°
Turns
0 Turns
C.C.W
54''
60''
48''
42''
48''
54''
54''
48''
48''
42''
5
6
5
6
42''
48''
36''
30''
36''
42''
42''
36''
36''
30''
3
4
3
4
