background image

Made In USA

Kit #05041

Skill Level 3

Skill Level 3

Average Skills Needed

The AeroDactyl TS  is a simple-to-build two-stage, payload 

carrying rocket that was designed around the Estes 29mm diameter 

rocket engines. These engines are low thrust, and therefore need 

a low weight rocket for maximum speed performance. With these 

motors, the rocket leaves a thick smoke trail as it zooms skyward.

The kit features a slotted body tube that allows the laser cut fins 

to mount perfectly straight on the rocket. This allows the rocket to fly 

straight and true. It also has a large payload bay, which can be used 

to fly things like altimeters and other scientific payloads. You’ll find 

that it is a very versatile rocket because it can be used with a variety 

of rocket motors. You can also fly the model as a single-stage vehi-

cle. With so many options it will never bore you.

AeroDactyl TS Parts List

Needed Tools and Materials

 

…

Hobby Knife with Sharp Blades

 

…

Ruler

 

…

Wood Glue (recommended) or White Glue

 

…

Sand Paper 200 grit

 

…

Masking Tape

 

…

Pencil

 

…

Scissors

 

…

Paper Tow

el

 

…

Wood Dowel

Optional Tools / Finishing Supplies

 

…

Super Glue (CyA Adhesive medium viscosity)

 

…

Plastic Sheet (to cover the work surface)

 

…

Paint Supplies: (Spray Paint, Brushes, etc)

 

…

Wood Sealer/Sanding Sealer

 

…

Safety Glasses (For general protection while building)

P/N 31105

Manufactured in the USA by:

Apogee Components Inc.

Colorado Springs, Colorado, USA

Visit us online at:

www.DynaStar-Rockets.com

 Item #  Item Name

Qty

10252 AT-29/5.25 Laser Cut Booster Stage Engine 

Mount Tube

1

10250 AT-29/7" Sustainer Stage Engine Mount Tube

1

10188 AT-66/18" Laser-Cut Sustainer Tube: 3-Slots

1

10189 AT-66/18" Laser-Cut Booster and Payload 

tube: 3 Slots

1

12381 CBD-66 Plywood Disk 

1

13039 AC-66A (Red) Laser-Cut

1

13044 AC-66A (Red)

1

13035 CR 24/29 (Green)

2

13315 CR 29/2.6"

4

13056 1/4" Launch Lug 3.0"

1

15565 AeroDactyl TS Sustainer Fin Sheet 1/8" Balsa

1

15566

AeroDactyl TS Booster Fin Sheet 1/8" Balsa

1

19480 Nose Cone PNC-66

1

23011 Parachute Rings

8

29117 DynaStar 32" Plastic Parachute

1

29500 Cotton Parachute String

21ft

29506 Kevlar Shock Cord 300#

10ft

29624 Wood Screw Eyelet Size 9

1

31105 AeroDactyl TS Instructions Sheet A 11x17

1

31106 AeroDactyl TS Instructions Sheet B 8.5x11

1

31107 AeroDactyl Fin Template Sheet

1

41012 AeroDactyl Decal

1

39034 AeroDactyl Face Card

1

Mid-Power Rockets

Содержание AeroDactyl TS








Отзывы: