Dynapac DRP45DX Скачать руководство пользователя страница 119

Страница: 119 / 124

9.8 DCI faults

Fault

Possible cause

Remedy

LED (a) flashes

Switching on: The LED (a) flashes for

approx 1

2 seconds after the vibration

has been switched on.

Vibration frequency too low

LED (a) lights up

No vibration detected

Start the engine, set the throttle lever to

position “MAX” (switch vibration on).

Check the connection of the acceleration

sensor.

Acceleration sensor is not connected.

Check the connection of the acceleration

sensor.

Cable breakage

Inform our Customer Service Department

The displayed

measuring values

are not plausible

The acceleration sensor is not fastened

correctly.

Shut down the engine and check the fas-

tening screws of the acceleration sensor.

Weak spots in the sub-base

In unfavourable cases, an excessively

varying material composition or moisture

in the sub-base can influence the meas-

uring results.

On material which is too dry or moist,

lower measuring values will be displayed.

5 6 7

B-DIS-1054

Fig. 144

Troubleshooting – DCI faults

DRP45DX

119

Содержание DRP45DX





























































































































Результаты поиска

Содержание DRP45DX

Отзывы:

Бренды по названию

Популярные бренды

Dynapac DRP45DX, Руководство по эксплуатации

Результаты поиска

Содержание DRP45DX

Отзывы:

Бренды по названию

Популярные бренды