Dynapac DFP12D Скачать руководство пользователя

Страница: 87 / 98

8.8 As required

8.8.1 Cleaning the cooling fins and the cooling air intake openings

How dirty the cooling fins and cooling air intake

openings are depends very much on the daily

operating conditions; clean daily if necessary.

Protective equipment:

Working clothes

Protective gloves

Safety goggles

Park the machine in secured condition

Chapter 6.5

„Parking the machine in secured condition“ on page 58

Allow the engine to cool down.

Remove dried dirt with a suitable brush from all cooling fins

and cooling air intake openings.

CAUTION!
Danger of eye injuries caused by particles

flying around!

–

Wear your personal protective equipment

(safety gloves, protective working

clothes, goggles).

Blow out the cooling fins and cooling air intake openings with

compressed air.

In case of damp or oily contamination you should consult our

customer service department.

8.8.2 Cleaning the machine

Protective equipment:

Working clothes

Protective gloves

Park the machine in secured condition

Chapter 6.5

„Parking the machine in secured condition“ on page 58

Let the machine cool down to ambient temperature.

Fig. 90

Maintenance – As required

DFP12D

Содержание DFP12D



































































































Результаты поиска

Содержание DFP12D

Отзывы:

Похожие инструкции для DFP12D

Бренды по названию

Популярные бренды

Dynapac DFP12D, Руководство по эксплуатации

Результаты поиска

Содержание DFP12D

Отзывы:

Похожие инструкции для DFP12D

Бренды по названию

Популярные бренды