Dynapac DFP12D Скачать руководство пользователя

Страница: 26 / 98

3.5 Loading/transporting the machine

Make sure that persons are not endangered by the machine tipping

or sliding off.

Do not use damaged or in any other way impaired lashing points.

Always use appropriate lifting and lashing means on the lifting and

lashing points.

Use lifting and lashing gear only in the prescribed direction of load

application.

Lifting tackle must not be damaged by machine components.

Secure the machine on the transport vehicle against rolling, slip-

ping and turning over.

Loads must only be attached and hoisted by an expert / capable

person.

Use only lifting gear and lifting tackle with sufficient load bearing

capacity for the weight to be loaded.

Fasten the lifting gear only at the specified lifting points.

Danger to the life of persons if they step or stand under a sus-

pended load.

When lifting the machine avoid uncontrolled movements of the

load. If necessary hold the load with guide ropes.

Concerning your safety – Loading/transporting the machine

DFP12D

Содержание DFP12D



































































































Результаты поиска

Содержание DFP12D

Отзывы:

Похожие инструкции для DFP12D

Бренды по названию

Популярные бренды

Dynapac DFP12D, Руководство по эксплуатации

Результаты поиска

Содержание DFP12D

Отзывы:

Похожие инструкции для DFP12D

Бренды по названию

Популярные бренды