(APD01•08)
3
57091
Bearing Press Tool
Balancer Shaft Assembly
Motor Shaft Balancer
57088 Bearing
57057
Front Bearing Plate
Drawing 4
57091
Bearing Press Tool
Balancer Shaft Assembly
Motor Shaft Balancer
57057 Front Bearing Plate
(with 57088 Bearing)
57056 Rear Bearing Plate
(with 01206 Bearing)
51354 Cylinder
Assembly.
(w/Rotor and Vanes)
Line-Up Pin
Drawing 5
Motor Assembly/Disassembly Instructions – 3" Dynabuffer
Important: Manufacturers warranty is void if tool is disassembled before warranty expires.
A complete Repair Kit, part number 96405, is available which includes special tools for correct disassembly/assembly of tool.
Drawing 1
57091
Bearing Press Tool
57088 Bearing
57057
Front Bearing Plate
Support
57091
Bearing Press Tool
Balancer Shaft Assembly
56052 Bearing
Shaft Step
Bearing Seal and
Bearing Shield
Drawing 2
Balancer Shaft Assembly
Motor Shaft Balancer
57088 Bearing
57091
Bearing Press Tool
Drawing 3
To Disassemble
1. Disconnect tool from power source.
2. Invert machine and secure in vice, using 57092 Collar (supplied in 96405 Repair Kit) or padded jaws.
3. Remove sanding pad with 26 mm open-end wrench (supplied with sander) and shroud or overskirt.
4. Insert 56058 Lock Ring Tool (supplied in 96405 Repair Kit) into corresponding tabs of lock ring and unscrew. Motor may now
be lifted out for service.
5. Remove 95626 Snap Ring.
6. Remove the rear plate and the cylinder assembly by securing the cylinder in a bearing separator gripped on the cylinder
exhaust and extra pocket area. Push the motor shaft balancer through the bearing.
7. Remove the rotor, vanes and rotor key from the motor shaft balancer. Remove the front plate using a small (#2) arbor press.
Support the edges of the front plate while pressing on the small end of the motor shaft balancer.
8. a.) If, during step 7, the front plate and 57088 Bearing remain together, press 57088 Bearing out of the front plate using
57091 Press Tool (supplied in 96405 Repair Kit) as shown in Drawing 1.
b.) If, during step 7, the front plate and 57088 Bearing remains on the motor shaft balancer, it can be removed with a
bearing separator.
9. Remove 01206 Bearing from the rear plate by using a bearing press tool.
10. Disassemble the balancer assembly as follows:
a.) Place motor shaft assembly into a soft jaw vise. Using a thin screwdriver, pick out the end of 95630 Snap Ring and peel
out. This will loosen the balancer assembly.
b.) Screw the female threaded portion of the 56056 Bearing Puller (supplied in 96405 Repair Kit) onto the 96416 Set Screw
of the balancer shaft and heat the outside of the motor shaft balancer to approximately 200° F (approximately 10
seconds with a propane torch). Now, using the slider weight, pull the assembly out.
c.) Press off 56052 Bearing with a bearing separator and remove bearing seal and bearing shield.
11. If during step 10, the 56052 Bearing remains in the motor shaft balancer, it can be removed by the heating the
shaft balancer again and using either an inside bearing puller or a blind hole bearing puller.
To Assemble:
Important: Be certain parts are clean and in good repair before assembling.
1. Assemble the balancer assembly as follows:
a.) Install 95630 Snap Ring onto balancer shaft. Install 95628 Shield with convex face toward hex of balancer shaft.
b.) Install 56053 Seal. Note: Be certain seal is pressed completely over shaft step.
c.) Apply 1 drop of #271 Loctite
®
(or equivalent) and spread over several places around the inside diameter of the 56052
Bearing and the outside diameter of the 57069 Balancer Shaft.
d.) Press fit 56052 Bearing with seal side toward hex of balancer shaft up to shaft step as shown in Drawing 2. This must
be a firm press fit for proper retention of bearing.
2. Place the motor shaft balancer in a soft jaw vise with large end-up.
3. Apply 1 drop of #271 Loctite
®
(or equivalent) and spread over several places around the outside diameter of the 56052 Bearing
and slide balancer assembly into the motor shaft balancer until 56052 Bearing is firmly seated at bottom. Squeeze 95630
Snap Ring into groove in motor shaft balancer to complete the assembly. Remove from vise.
4. Press 57088 Bearing onto the motor shaft balancer down to the shoulder as shown in Drawing 3.
5. Press 57057 Front Bearing Plate onto 57088 Bearing as shown in Drawing 4 and check for smooth rotation.
6. Place the 57090 Rotor and 56047 Rotor Key on the motor shaft balancer. Place the 56073 Vanes into the rotor slots.
Note: Vanes should be lightly lubricated with Dynabrade Air Lube P/N 95842 (or equivalent) before installation.
7. Place 51354 Cylinder with 95571 Pin over rotor. The “short” line-up pin goes toward the Front Plate.
8. Place 57056 Rear Bearing Plate (with 01206 Rear Bearing pressed into place) over shaft and “long” end of line-up pin and
press fit in place as shown in Drawing 5.
9. Place 95626 Snap Ring in groove.
10. Secure motor housing in vise, using 57092 Collar or padded jaws. Spread 2-3 drops of pneumatic tool oil around the housing
bore for ease of insertion of motor assembly. Slide motor assembly into secured housing. Note: Be certain line-up pin enters
the hole in the bottom of the housing.
11. Install 50659 O-Ring into 56046 Lock Ring.
12. Tighten lock ring with 56046 Lock Ring Tool to 34 N•m/300 in. - lbs. Attach shroud and buffing back-up pad.
Tool Assembly Complete. Please allow 30 minutes for adhesives to cure before operating tool.
Valve and Speed Regulator Assemblies:
1. Secure housing in vice using 57092 Collar or padded jaws.
2. Remove 56076 Valve Plug. Remove the 95523 O-Ring.
3. Remove 54192 Spring, and 56029 Valve Stem with o-ring.
4. Install new 95523 O-Ring onto 56076 Valve Plug, and new 01020 O-Ring onto 56029 Valve Stem.
5. Place valve stem into housing, alone with 54192 Spring.
6. Install 56076 Valve Plug and new 95523 O-Ring.
(continued on next page)
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade