dymax Edge-Carry страница 27 Скачать руководство пользователя

Страница: 27 / 32

Dymax Edge-Carry Conveyor User Guide

Troubleshooting

Table 8. Troubleshooting Chart for the EC-Series Flood Lamps

Problem

Possible Cause

Testing

Corrective Action

Lamp Will Not
Ignite

or

Lamp Flickers,

Won’t

Maintain
Operation

Improperly Fastened
Connections

Visually inspect all connections to
and from the Power Supply.

Secure all connections.

Main Line Fuse
Blown

Remove Fuse from Power
Receptacle and check with an
Ohmmeter.

Replace Fuse, if defective.

Corroded Lamp
Bases

Visually inspect the Lamp Bases for
ANY signs of corrosion.

Replace the Lamp Bases if
corrosion exists (both Lamp Bases
should be replaced at the same
time).

Lamp Beyond Useful
Life

Replace Lamp with known good
Lamp and re-test unit.

Replace Lamp if defective (typical
Lamp life = 2,000 hours).

Power Supply Board
Failed

Check UV output voltage on Power
Supply Board. Set Oscilloscope to:
20ms/div 100V/div

Replace power supply board if
defective.

Igniter
Malfunctioned

Verify open circuit voltage from
Igniter. Set Oscilloscope to:
50us/div 1000V/div

Replace if defective.

EC Power
Supply Blows
Input Fuse

Malfunction in the
Power Supply Board

Remove power. Disconnect the
Lamp/Reflector Assembly from the
Power Supply. Replace the Fuse.
Apply power. If Fuse blows, Power
Supply is defective.

Replace the Power Supply Board.

UV Intensity
Appears To Be
Low

Lamp Beyond Its
Useful Life

Use a Radiometer to measure
actual output intensity. Consult
manual for proper output.

Replace Lamp if beyond useful life
(Typical Lamp life = 2,000 hours).

Quartz Envelope on
Lamp Contaminated

Visually inspect the Lamp for signs
of contamination (Quartz Envelope
MUST be free from ANY
contamination).

Clean the Lamp with a soft, lint-
free cloth and isopropyl alcohol.
Lamp may have to be replaced if
contamination is burned into
Quartz Envelope.

Surfaces Of Reflector
May Be
Contaminated

Examine Reflector for
contaminants (should be a clean,
shiny surface).

Clean Reflector with a soft, lint-
free cloth and isopropyl alcohol or
equivalent.

Glass Filter
Contaminated
(2000-EC Only)

Examine Glass Filter for signs of
contamination.

Clean Glass Filter with a soft, lint-
free cloth and isopropyl alcohol or
equivalent.

Reflector
temperature is too
low (5000-EC Flood
Lamps).

Verify Reflector temperature is
between 115° F and 145° F as
measured at the temperature
indicator on top of the Reflector
Housing.

Adjust Conveyor Temperature
Control Plates or add/remove
Reflector Ventilation Plates as
necessary to achieve proper
temperatures.

Содержание Edge-Carry

































Результаты поиска

Содержание Edge-Carry

Отзывы:

Похожие инструкции для Edge-Carry

Бренды по названию

Популярные бренды

dymax Edge-Carry, Руководство пользователя

Результаты поиска

Содержание Edge-Carry

Отзывы:

Похожие инструкции для Edge-Carry

Бренды по названию

Популярные бренды