background image

- 1 -

INSTALLATION INSTRUCTIONS

Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017

SA

VE FOR FUTURE USE

RECOMMENDED TOOLS AND MATERIALS

Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing 
supply stores. It is essential that the tools and materials be on hand before work is begun.

M965560  Rev. 1.3 (5/17) 

Lavatory  

Model D35102100
Vessel

 

Model D35102150

Model D35102151

Randall

®

  

Single Lever Lavatory

and Vessel Faucets

ROUGHING-IN DIMENSIONS: 

• For reference

 NOTE:

 MOUNTING HOLES ARE 1-3/8" D.

4-3-16"

(106 mm)

4-1/4"

(108 mm)

8-1/2"

(216 mm)

MTG.

SURFACE

24"

(610 mm) 

6"

(152 mm)

1-3/4" (45 mm)

2-3/4" DIA.

(70 mm)

3/8" (10 mm)

SUPPLIES

12" MAX.

(305 mm)

MAX 2"

(51mm)

1-1/4" O.D.

(32 mm) 

NOTE: MOUNTING HOLE

1-3/8" DIA. (35 mm)

12-5/16"

(316 mm)

4-1/8"

(105 mm)

8-1/8"

(206 mm)

3-1/16" DIA.

(77 mm)

6"

(152 mm)

MTG.

SURFACE

24"

(610 mm) 

2-1/16" MAX. (53 mm)

12" MAX.

(305 mm)

MAX 2"

(51 mm)

1-1/4" O.D.

(32 mm) 

3/8" (32 mm)

SUPPLIES

 

Flat Blade Screwdriver    

Plumber’s Putty or Caulking

Adjustable Wrench    

Tubing Cutter 

Channel Locks

In the United States:

DXV

One Centennial Avenue 

Piscataway, New Jersey 08855

Attention: Director of Customer Care

For residents of the United States, warranty 

information may also be obtained by calling 

the following toll free number: (800) 227-2734

www.DXV.com

In Canada:

DXV 

5900 Avebury Road  

Mississauga, Ontario  

L5R 3M3 

Canada

Toll Free: 1-800-387-0369

Local: 905-306-1093 

Fax: 1-800-395-1498 

www.DXV.ca

In Mexico:

DXV 

Via Morelos 330 

Col. Santa Clara Coatitla  

Ecatepec, Estado de México 55540

Toll Free: 01-800-8391200

www.DXV.mx

Thank you for selecting DXV. To ensure that your 
installation proceeds smoothly, please read these 
instructions carefully before you begin.

Содержание Randall D35102100









Отзывы: