Dvorak Spider ILD01G Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 53

Dvorak Spider ILD01G Скачать руководство пользователя страница 47

Operation manual - Spider ILD01G

47 / 53

rev. 02-15-02-2017

11.23 TECHNICAL PLATE

The technical plate provides information on mower fillings and basic information for machine
maintenance. The technical plate is placed on the machine girder.

- Engine
- Engine oil
- Oil quantity
- Spark plug
- Fuel
- Hydraulic system
- Hydraulic oil
- Oil quantity
- Electronic system
- Battery
- Fuses
- Tires
- Tire type
- Maximal pressure
- Lubrication
- Chain gears
- Sliding surfaces

11.24 TOOLS

Spider ILD01 is equipped with a basic set of tools, which allow regular maintenance and basic servicing. The tools
are based under the side cover upon to the Fuel tank (see figure below). The tool roll is also equipped with a
pocked for the business card of your local authorized service/dealer.

List of tools

Use

Placement on the machine

Spark plug spanner 19, 21 mm

Spark plugs

Socket head 19 mm

Change of blades

Socket head 17 mm

Change of wheels

Socket head 15 mm

Tightening of drive belts

Lever handle

-

Flat spanner 10-13 mm

Tightening of drive belts

Flat spanner 16-17 mm

By-pass, tightening of steering
chain

Hex-wrench IMBUS 3 mm

Wheel suspension

Hex-wrench IMBUS 5 mm

Wheel suspension

Hex-wrench IMBUS 6 mm

Wheel suspension

Hex-wrench IMBUS 8 mm

Tightening of steering chain

Screwdriver flat-tip / crossshead

Fuse box

Fuses 5A, 20A

Fuse box

«
...
45
46
47
48
49
...
»

Содержание Spider ILD01G






















































Отзывы:

Нет отзывов