DV8 OFFROAD TSJL-03 Скачать руководство пользователя страница 1

Страница: 1 / 13

6400 SYCAMORE CANYON BLVD.

RIVERSIDE, CALIFORNIA 92507

855-680-9595

WWW.DV8OFFROAD.COM

855-680-9595

NEED HELP?

PRODUCT

INSTALLATION

MANUAL

Spare Tire Delete with Optional

Dual Light Pod Mounts

2018+ JL
TSJL-03

TOOLS

REQUIRED

SKILL

LEVEL

TIME

REQUIRED

- #4, #5 Allen Head
- T8, T25, T30 Torx Bit
- 7, 10, 13, 22mm Sockets
- Plastic Trim Tool
- Small Phillips Head Screwdriver
- Medium Flat Head Screwdriver
- Snips or Grinder

Before you install this kit —

Read and understand all

instructions, warnings, cautions, and notes contained in

this installation instruction guide. Consult your vehicle

owner’s manual for proper disconnection of electrical and

lifting of vehicle if required for installation of this product.
This install may require some technical skills and

knowledge of basic mechanical work. If you do not feel that

you are capable of performing this install please take this

product to a trained professional.
After reading this guide please contact us with any

questions or concerns before installing product.

Customer Service: 855-680-9595

DV8 Offroad is not responsible for any bodily injury or harm

to you or your vehicle as a result of an improper install.

Proper installation of this kit required knowledge of the factory

recommended procedures for removal and installation of original

equipment components. We recommend that the factory shop manual

and any special tools needed to service your vehicle be on hand during

the installation. Installation of this kit without proper knowledge of the

factory recommended procedures may affect the performance of these
components and the safety of the vehicle

• Always wear eye protection when operating power tools

Inspect all contents of this package to make sure product is not

damaged and all installation hardware has been included. If parts

are missing from kit, please be prepared to provide the following

information

1. Name of purchase location
2. Bar Code on side of box
3. Date above bar code
4. Date inside box cover

- Novice/Intermediate
- 1 (you)

Little skill level required, you can

easily install it by yourself however,

additional help will be useful

- Approximately 2 Hours

Time to install this should only

take about approximately 2

Hours

WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION

Содержание TSJL-03














Результаты поиска

Содержание TSJL-03

Отзывы:

Бренды по названию

Популярные бренды

DV8 OFFROAD TSJL-03, Руководство по установке

Результаты поиска

Содержание TSJL-03

Отзывы:

Бренды по названию

Популярные бренды