background image

6

CDW247001

30004577

hotter surfaces of the stove, and is caused by the heat 
radiating through the paint. It is also expected that shiny 
spots caused by friction from the packaging materials, 
will disappear during the curing of the stove.

SO:

1.  Remember to ventilate well.
2.  Allow the stove to cure before burning for long peri-

ods at high temperatures.

3.  Flat spots on the painted surfaces are normal.
4.  Shiny spots on the paint surface before burning is 

normal.

5.  Call your dealer if you have any questions.

Building a Fire

Never use gasoline, gasoline-type latern fuel, ker-
osene,  charcoal  lighter  fluid  or  similar  liquids  to 
start or ‘freshen up’ a fire in this heater. Keep all 
such liquids well away from the heater while it is 
in use.

Inlet Air Control Settings

 

Desired 

 

Inlet 

 

**Approx. 

 

Burn Setting 

Air Setting 

BTU Output

 

Low 

Closed Fully 

11,492

  Med / Low 

1/4 Open 

11,721

  Med / High 

3/4 Open 

15,501

 

High 

Fully Open 

18,920

1.  Open inlet air control fully.
2.  Place a small amount of crumpled paper in the 

stove.

3.  Cover the paper with a generous amount of kindling 

in a teepee fashion and a few small pieces of wood.

4.  Ignite the paper and close door. If fire dies down 

substantially, open door slightly.

5.  Add larger pieces of wood as the fire progresses be-

ing careful not to overload. Do not fill firebox beyond 
firebrick area. An ideal coal bed of 1” to 2” should be 
established to achieve optimum performance.

6.  This unit is designed to function most effectively 

when air is allowed to circulate to all areas of the 
firebox. An ideal means of achieving this is to rake a 
slight (1” to 2” wide) trough in the center of the coal 
bed from front to back prior to loading the fuel.

7.  Once fuel has been loaded, close the door and open 

air inlet control fully until fire is well established (ap-
prox. 10 minutes) being careful not to overfire.

8.  Readjust air inlet control to desired burn rate. If 

excessive smoke fills firebox, open air inlet control 
slightly until flames resume and wood is sufficiently 
ignited. While a basic rule of thumb is “closed-low”, 
“1/2 way - medium” and “fully open-high”, refer to the 
Inlet Air Control Settings chart.

9.  When refueling, adjust air control to the fully open 

position. When fire brightens, slowly and carefully 
open the door. This procedure will prevent gases 
from igniting causing smoke and flame spillage.

10.Add fuel being careful not to overload.

Glass Care

The following use and safety tips should be observed.
1.  Inspect the glass regularly for cracks and breaks. If 

you detect a crack or break, extinguish the fire im-
mediately and contact your dealer for replacement.

2.  Do not slam door or otherwise impact the glass. 

When closing doors, make sure that logs or other 
objects do not protrude and impact the glass.

3.  Do not clean the glass with materials which may 

scratch (or otherwise damage) the glass. Scratches 
on the glass can develop into cracks or breaks.

4.  Never attempt to clean the glass while unit is hot. If 

the deposit is not very heavy, normal glass clean-
ers are adequate with a plain, nonabrasive scouring 
pad. Heavier deposits may be removed with the use 
of a readily available oven cleaner.

5.  Never put substances which can ignite explosively 

in the unit since even small explosions in confined 
areas can blow out the glass.

6.  This unit has an airwash system, designed to reduce 

deposits on glass.

Replace glass only with high temperature Robax 
Pyroceram of the proper size and thickness.

Gasket Replacement

After extensive use, the sealing material which provides 
glass and door seal may need to be replaced if it fails 
to sustain its resilience. Inspect glass and door seal pe-
riodically to ensure for proper seal. If gaskets become 
frayed or worn, replace immediately.
Contact your dealer for approved replacement parts.
The following steps should be followed for glass gasket 
replacement:
1.  Ensure appliance is not in operation and has thor-

oughly cooled.

2.  Remove screw and glass clip.
3.  Lift glass out from glass clip.
4.  Remove old gasket and clean glass.
5.  Replace new gasket starting at the bottom of glass 

working along edges, being sure to center gasket 
channel on glass. 

6.  Trim to length and butt ends together.

Содержание DutchWest CDW247001

























Отзывы: