manualshive.com logo in svg

Durr Dental VistaScan Mini View, Инструкция по установке и эксплуатации

Поделиться
Скачать
Durr Dental VistaScan Mini View Скачать руководство пользователя страница 46

44 

2142100002L02  1908V007 

14  Tips for operators and service technicians

Any repairs exceeding routine maintenance may only be carried out by qualified personnel or 
our service.

Prior to working on the unit or in case of danger, disconnect it from the mains.

14.1 Poor X-ray image

Fault

Probable cause

Solution

X-ray image does not ap-
pear on the monitor after 
scanning

Image plate inserted the wrong 
way round, inactive side was 
scanned

 

i

Scan the image plate again im-
mediately, making sure you feed 
it in correctly in the process.

Image data on the image plate 
has been erased, e.g. by ambient 
light

 

i

Always scan the image data of 
the image plate as quickly as 
possible.

Fault on the unit

 

i

Inform a Service Technician.

No image data on image plate, 
image plate not exposed

 

i

Expose the image plate.

X-ray unit is faulty

 

i

Inform a Service Technician.

X-ray image too dark

X-ray dose too high

 

i

Check X-ray parameters.

Incorrect brightness/contrast set-
tings in the software

 

i

Adjust the brightness of the X-
ray image in the software.

X-ray image too bright

Exposed image plate has been 
exposed to ambient light

 

i

Always scan the image data of 
the image plate as quickly as 
possible.

X-ray dose too low

 

i

Check X-ray parameters.

Incorrect brightness/contrast set-
tings in the software

 

i

Adjust the brightness of the X-
ray image in the software.

X-ray image only shadowy

The X-ray dose on the image 
plate was insufficient

 

i

Increase X-ray dose.

Amplification (HV value) is set too 
low in the software

 

i

Increase amplification (HV value).

Unsuitable scanning mode select-
ed

 

i

Select a suitable scanning 
mode.

The setting for the threshold value 
is too high

 

i

Reduce the threshold value.

Troubleshooting

EN

Содержание VistaScan Mini View

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды