Durr Dental Vector Scaler Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 48

Durr Dental Vector Scaler Скачать руководство пользователя страница 39

9000-615-32/02 1808V002

37

Usage

Disinfect using Vector/RinsEndo Disinfection:

i

Pour 2 sealing caps (approx 40 ml) of

Vector/

RinsEndo disinfection

into the fluid container

2x

i

Touch the RINSE (rinsing/disinfecting) button
for at least 2 seconds

RINSE

i

LED flashes – the

Vector/RinsEndo Disinfec-

tion

is rinsed into the system and the process

ends automatically The

Vector/RinsEndo

Disinfection

remains in the system until the

next treatment

i

Empty any remaining

Vector/RinsEndo Disin-

fection

from the fluid container

i

Thoroughly rinse the fluid container with water
and dry

14.2 Initial start-up after a break

in treatment for more than
24 hours

The initial start-up process will depend upon
whether the hose system was reprocessed be-
fore the break in treatment Proceed as follows
depending on the situation:

1. Reprocessing performed before the treat-
ment break:

i

Rinse the system with water

Thorough rinsing with water will flush out
any disinfectant remaining in the hoses,
and any irritation to the patient caused by
the taste of residual disinfectant will be
avoided

i

Pull off the hose connection from the hand-
piece

i

Lay the handpiece hose in the sink

i

Fill the fluid container with water

i

Touch the RINSE (rinsing/disinfecting) button
for at least 2 seconds
LED flashes – the rinsing process takes
around 30 seconds and ends automatically

14 Treatment breaks for more

than 24 hours

If no treatment is carried out for a period of
24 hours or more, reprocessing of the hose sys-
tem must be performed

14.1 Cleaning and disinfecting the

hose system

The hose system is disinfected using a ready-
to-use, aldehyde-free solution of

Vector/Rin-

sEndo Disinfection

i

Pull off the hose connection from the hand-
piece

i

Lay the handpiece hose in the sink

Rinsing with water:

i

Fill the fluid container to approx 1/3 with wa-
ter

i

Touch the RINSE (rinsing/disinfecting) button
for at least 2 seconds

RINSE

i

LED flashes – the rinsing process takes
around 30 seconds and ends automatically

i

Rinsing with water will flush out any remaining
blockage

i

After the end of the rinsing process drain any
remaining fluid in the system

EN

«
...
37
38
39
40
41
...
»

Содержание Vector Scaler

















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды