Durr Dental 5286100036 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 36

background image

13.2 Replacing the air intake filter

❯

Switch the compressor to standby mode with
the standby button.

❯

Unplug the mains plug.

❯

Take off the noise reducing hood and the foam
filter cover.

2

1

❯

Release the filter cover by rotating it

anti-

clockwise

and then take it off.

2

1

❯

Remove the air intake filter.

❯

Insert a new air intake filter.

❯

Place the filter cover in position and lock it by
turning it

clockwise

.

❯

Fit the the foam filter cover and the noise
reducing hood.

13.3 Replacing the filter of the

membrane drying unit

Fine/sterile filter

❯

Switch off the unit.

❯

Disconnect all power from the device.

❯

Unscrew and remove the filter cover.

❯

Remove the fine/sterile filter.

❯

Insert the new fine/sterile filter.

❯

Replace the filter cover and close.

Usage

5286100072L02 1909V005

25

EN

«
...
25
26
27
28
29
...
»

Содержание 5286100036





































Отзывы:

Нет отзывов

Похожие инструкции для 5286100036

Бренд: ABB Страницы: 36

Бренд: ABB Страницы: 40

Бренд: ABB Страницы: 18

Бренд: R-Tech Страницы: 3

Бренд: Landoll Страницы: 34

Бренд: GE Страницы: 698

ST60+ SPEED INSTRUMENT

Бренд: Raymarine Страницы: 60

Бренд: Raymarine Страницы: 15

Бренд: RaycoWylie Страницы: 9

Бренд: Raven Страницы: 58

Бренд: Raven Страницы: 26

Бренд: Ravo Страницы: 114

Бренд: Alcoscan Страницы: 6

Бренд: YASKAWA Страницы: 40

RAISED GARDEN BED

Бренд: Yardfully Страницы: 2

Бренд: Dantel Страницы: 22

Бренд: Kärcher Страницы: 148

Бренд: Martin Страницы: 202

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды