AC/DC DUAL CHARGER
WITH
BALANCING
Quick Reference Guide to Programming
NOTE:
This guide does not replace the entire instruction manual as supplied with this charger. Read
the provided manual in its entirety before use, paying particular attention to all safety warnings!!
™
DTXP4255 QRG
1.
Output 1 and Output 2 are independent. Connect the battery to one output and use the appropriate screen and controls for that output.
2. START:
Connect the charger to power. The
CHARGE START
screen will appear, with the active battery memory number shown in the
top right corner (>0<). All settings for this memory will automatically scroll across the bottom of this screen or can be scrolled through using
the
▼
and
▲
buttons.
If these settings are acceptable
for the battery to be charged, press
and hold
START
and charge will begin.
3. SELECT A MEMORY:
All ten memory profi les are pre-programmed with charge settings as
shown in the chart. Press
CHANGE
then
▼
or
▲
to fi nd the correct profi le. Press
CHANGE
again
to confi rm. Press
and hold
START
and charging will begin.
4. MANUAL SETUP:
Follow the steps below
to fi nd the
BATTERY SETUP
screen to adjust
the charger settings to match a specifi c battery.
PRESS
PRESS
PRESS
PRESS
PRESS
PRESS
PRESS
PRESS
PRESS
PRESS
PRESS
PRESS
PRESS
PRESS
PRESS
TO
CHARGE
START
SCREEN
BATTERY TYPE:
Press
CHANGE
,
then
▼ ▲
to find the proper battery type.
Press
CHANGE
to confirm.
CELL[02]:
Press
CHANGE
, then
▼▲
to
find the proper number of cells in the
battery (confirmed by the voltage shown
at the bottom of the screen). Press
CHANGE
to confirm.
CAPACITY:
Press
CHANGE
, then
▼▲
to find the rated capacity value of the
battery. Press
CHANGE
to confirm.
CURRENT:
Press
CHANGE
, then
▼▲
to find the desired current. Press
CHANGE
to confirm.
S_TIMER:
Press
CHANGE
, then
▼▲
to
find the desired backup safety timeout for
charge. Press
CHANGE
to confirm.
MELODY:
Press
CHANGE
, then
▼▲
to
change the melody type. Press
CHANGE
to confirm.
BEEP OFF:
Press
CHANGE
, then
▼▲
to turn ON or OFF. Press
CHANGE
to
confirm.
INPUT VOLTAGE:
Shows the voltage
at the charger’s input.
OUTPUT VOLTAGE:
Shows the
voltage at the charger’s output.
PEAK VOLTAGE:
Shows the maximum
voltage measured on the battery during
charge.
CHG CAPACITY:
Shows how much
energy was delivered to the battery during
charge.
CHG TIME:
Shows how many minutes
elapsed during the charge process.
5. START CHARGE:
After all settings are made, press until the
CHARGE START
screen shows. Press and hold
START
for 2 seconds
and fast charge will begin.
MEMORY NO.
Battery Type
Cell Count
Capacity (mAh)
Current
Safety Time (minutes)
Delta Peak (mV/C)
Trickle Current (mA)
0
LiPo
2
4000
4.0A
120
–
–
1
LiPo
2
5000
5.0A
120
–
–
2
LiPo
2
5700
5.7A
120
–
–
3
LiPo
3
5000
5.0A
120
–
–
4
LiPo
3
6400
6.4A
120
–
–
5
NiCd
6
1800
1.8A
90
10
200
6
NiMH
6
3000
3.0A
90
8
250
7
NiMH
6
5000
5.0A
90
8
250
8
NiMH
7
3000
3.0A
90
8
250
9
NiMH
7
5000
5.0A
90
8
250
WARNING!!
NEVER LEAVE A BATTERY UNATTENDED WHILE BEING CHARGED! REFER
TO THE PROVIDED INSTRUCTION MANUAL FOR FULL DETAILS.