Duplo DF-990 Скачать руководство пользователя

Страница: 61 / 100

Chapter 3 Advanced Operation

Set the feeding pressure adjustment

lever to [3].

• Set the paper feed pressure within the [3]

to [5] range on the scale.

• When paper mis-feed occurs, increase the

paper feed pressure to [4] or [5].

Set the separating pressure adjustment

dial to [2.5].

If double-feed occurs, increase the separating

pressure by [0.5] at a time.

Press the

key to test fold.

Check the finish.

If abnormal folding occurs, decrease the processing speed.

After completing folding operation of art paper or coated paper, return the paper feeding

pressure and separating pressure each to [0]. If fine quality paper is used with the paper feed

pressure and separating pressure set to the values for art paper and coated paper, double-feed

may occur, or leading edge of paper may be damaged.

5-2. Rough paper, recycled paper

Some recycled paper may be thin, flimsy and easy to curl when copied, and therefore inappropriate for

folding. When folding such paper, pay attention to the following points.

• Separate the paper well prior to stacking on the paper feed tray.
• Set the processing speed as low as possible.

If set to high, wrinkles or deformed folding will result.

• Set the paper feed pressure as low as possible.

If set to high, double-feed will result.

• Set the paper separating pressure as low as possible.

If set to high, the center of the lead edge of the paper may be scratched or turned over.

Содержание DF-990





































































































Результаты поиска

Содержание DF-990

Отзывы:

Похожие инструкции для DF-990

Бренды по названию

Популярные бренды

Duplo DF-990, Инструкция по эксплуатации

Результаты поиска

Содержание DF-990

Отзывы:

Похожие инструкции для DF-990

Бренды по названию

Популярные бренды