Duplo DF-755 Скачать руководство пользователя

Страница: 73 / 86

4-9

Chapter 4 TROUBLESHOOTING GUIDE

3. Error Messages

When a paper jam has occurred or the top cover is open, an error message is displayed on the LCD

display.
Follow the procedures below to fix the error.

Message

Cause

Solution

NO PAPER

When the power is turned on, there

is no paper on the paper feed ta-

ble.

Stack paper on the paper feed

table.

NO PAPER/****(the number of

folded paper)

After paper is fed and folded, there

is no paper left on the paper feed

table.

Stack paper on the paper feed

table. The number of folded paper

will be displayed again.

COVER OPEN

The top cover is open.

Close the top cover.

PAPER ERR

A paper jam has occurred.

Remove the jammed paper and

press the C (clear) button.

( p.1-11, p.4-3)

A mis-feed has occurred.

Stack paper properly on the paper

feed table and press the C (clear)

button. ( p.1-11, p.4-3)

PLATE-1 SET ERR

The first folding plate has not been

installed properly.

Install the first folding plate prop-

erly. ( p.1-6)

PLATE-2 SET ERR

The second folding plate has not

been installed properly.

Install the second folding plate

properly. ( p.1-6)

OVER LOAD

The motor is overloaded.

Turn off and on the power.

Содержание DF-755























































































Результаты поиска

Содержание DF-755

Отзывы:

Похожие инструкции для DF-755

Бренды по названию

Популярные бренды

Duplo DF-755, Инструкция по эксплуатации

Результаты поиска

Содержание DF-755

Отзывы:

Похожие инструкции для DF-755

Бренды по названию

Популярные бренды