Duplo DF-755 Скачать руководство пользователя

Страница: 64 / 86

3-30

Chapter 3 ADVANCED OPERATION

5-2. Correcting Folding Misalignment along Sides of Paper

Paper feeding

direction

When folded paper is misaligned along the sides
of paper as shown in the figure, turn the slant correction
knob to correct the misalignment.

You may need fine adjustments according to various conditions such as environmental

conditions (temperature, humidity), paper quality, paper thickness, paper fiber direction,

cutting accuracy and printing conditions.

Slant correction knob

Turn the slant correction knob to ad-

just the folding slippage.

Slant correction knob

If folding slippage is as shown in Figure A,

turn the knob in the direction of the arrow.

Slant correction knob

If folding slippage is as shown in Figure B,

turn the knob in the direction of the arrow.

Round hole

Slant correction knob

After finishing operations, be sure

to turn the slant correction knob to

align the round holes of the paper

feed table with the pin.

The position at which the round hole meets

the pin is the standard position.

Содержание DF-755























































































Результаты поиска

Содержание DF-755

Отзывы:

Похожие инструкции для DF-755

Бренды по названию

Популярные бренды

Duplo DF-755, Инструкция по эксплуатации

Результаты поиска

Содержание DF-755

Отзывы:

Похожие инструкции для DF-755

Бренды по названию

Популярные бренды