Duplo DF-755 Скачать руководство пользователя

Страница: 45 / 86

3-11

Chapter 3 ADVANCED OPERATION

2. Custom Folding of Standard Paper

Custom folding is the method of folding paper where you specify the folding stoppers of the first and

second folding plates. The following describes the custom folding procedures taking accordion fold as

an example.

Side guide

Fixing screw

Side guide

Fixing screw

Loosen the fixing screws of the side

guides, and move the side guides to

fit the paper width.

Paper

Paper set lever

Guide plate

Raise the paper set lever and place

some paper on the paper feed table.

Push in the paper until its lead edge touch-

es the guide plate.

Side guide

Fixing screw

After pressing the side guide to each

side of the paper lightly, tighten the

screws to secure the side guides.

Paper set lever

Lower the paper set lever.

The paper feed table will be raised.

Make sure that you lower the paper set

lever. If you start operations without the

paper set lever lowered, the paper feed

rings will run idle, causing the machine

to stop.

Содержание DF-755























































































Результаты поиска

Содержание DF-755

Отзывы:

Похожие инструкции для DF-755

Бренды по названию

Популярные бренды

Duplo DF-755, Инструкция по эксплуатации

Результаты поиска

Содержание DF-755

Отзывы:

Похожие инструкции для DF-755

Бренды по названию

Популярные бренды