Duplo DF-755 Скачать руководство пользователя

Страница: 17 / 86

1-5

Chapter 1 BEFORE OPERATION

2-3. Locking the Bearing Support Levers

The bearing support levers are released at shipment to prevent the rubber roll from becoming

distorted. After removing the press release levers, be sure to lock the bearing.

Support paper

feed plate

Paper receiving stopper

Paper

receiving

tray

Unfold the paper receiving tray.

Unfold the support paper feed plate.

• If you unfold the support paper feed

plate before unfolding the paper re-

ceiving tray, the paper receiving stop-

per may be damaged. Make sure that

you unfold the paper receiving tray

first.

• The paper receiving tray and sup-

port paper feed plate are foldable so

that you can easily move or store the

machine. Make sure that you unfold

them before using the machine.

Top cover

Open the top cover.

Bearing support lever

Operator’s side

Turn the bearing support lever on the

operator's side in the direction of the

arrow.

The bearing will be locked.

Содержание DF-755























































































Результаты поиска

Содержание DF-755

Отзывы:

Похожие инструкции для DF-755

Бренды по названию

Популярные бренды

Duplo DF-755, Инструкция по эксплуатации

Результаты поиска

Содержание DF-755

Отзывы:

Похожие инструкции для DF-755

Бренды по названию

Популярные бренды