Duplo DF-755 Скачать руководство пользователя

Страница: 16 / 86

1-4

Chapter 1 BEFORE OPERATION

2-2. Removing the Press Release Lever

The press release levers are attached to the unit at shipment to prevent the rubber roll from becoming

distorted. Be sure to remove them when setting up the machine.
The two types of press levers are attached to either side of the rubber roll.

Press release lever (A)

Operator’s side

Rubber roll

Press release lever (B)

Press release lever (A)

Press release lever (B)

Rubber roll

Non-operator’s side

The machine will be damaged if it is used without removing the lever.

To remove the press release lever (A) on the non-operator's side, push it inwards

and pull it out.

Press release lever (A)

To remove the press release lever (A) on the operator's side, push it inwards and

pull it out.

To remove the press release lever (B) on the non-operator's side, push it inwards

and pull it out.

Press release lever (B)

To remove the press release lever (B) on the operator's side, push it inwards and

pull it out.

Содержание DF-755























































































Результаты поиска

Содержание DF-755

Отзывы:

Похожие инструкции для DF-755

Бренды по названию

Популярные бренды

Duplo DF-755, Инструкция по эксплуатации

Результаты поиска

Содержание DF-755

Отзывы:

Похожие инструкции для DF-755

Бренды по названию

Популярные бренды