background image

PT-212

 

1

 

Kit No. 1257

 

PT-212 

Kit No. 1257 

 
 

INTRODUCTION  

THIS IS A TOY!

 

Modeling should be fun, so don’t sweat the small stuff.  Enjoy the 

experience.  This kit is fun to build as is, and at the same time, gives you, the builder, and those of 
you who like to tinker, the foundation to let your imagination to go hog wild.  Just remember one 
very important thing, there are NO model police, this is just a toy.
 

Before you start any construction, please read the entire instruction booklet to acquaint 

yourself with the building sequence of this kit.   

We who have designed the kit and have written the instructions have tried to make all of 

the contents as accurate and correct as possible.  Drawings and text have been thoroughly 
checked and crosschecked.  However, due to the variability of material, personal skills, and so on, 
neither the designer, nor Dumas Products Inc., assumes any responsibility for any damages or 
other losses incurred that have resulted from misuse of the material presented here.  All 
instructions and drawings should be carefully studied and clearly understood before beginning this 
project. 

Experienced modelers can jump into building this model and use whatever construction 

sequence and materials that appeal to them.  The less experienced modelers would do better to 
follow the steps in the numbered sequence. The model was designed to make its building as 
foolproof as possible.  However, I recognize that nothing is proof against a really determined fool. 

When a more detailed explanation is needed to clarify a particular building operation, a 

detailed drawing is included indicated by a figure number.  This drawing can then be found on the 
larger sheet (11 x 17), which will be easier to see and read.  

Also enclosed is the Parts List.  Please do a complete inventory of the kit and contact us 

at 1-800-458-2828 if anything is missing. To process your order more efficiently, please have the 
PART NAME AND NUMBER ready when you call. 

Содержание 1257











































Отзывы: