Dukane Infinity 43NSLA Скачать руководство пользователя страница 57

Страница: 57 / 65

CTION

8 |

LARM

M
ESS
A

GES

Infinity™

Series Servo Ultrasonic Press Systems QUICK START GUIDE

The following lists of alarms, on pages 53-56, that may appear on the servo press systems containing a generator with a
color front panel display or IQ Explorer 3 software.
Information on particular alarms may also be obtained on the Dukane '"Easy Alarm" web page below:

https://support.dukane.com/EasyAlarm

Alarm Code

Alarm Message

Explanation

Solution

U100

Configuration Fault

Default Setup corrupted, Model Number in-

correct, Serial Number incorrect, Feedback

Scaling incorrect, etc.

This is a disabling condition for the generator; contact

Dukane.

U101

Bad Parameter Alarm

Internal generator fault.

Contact Dukane.

U102

Watchdog reset Alarm

Internal generator fault.

Contact Dukane.

U103

Hardware Fault

Hardware configuration or options were

changed since last generator power up.

This is a disabling condition for the generator; contact

Dukane.

U104

Frequency Overload Fault

1 (PLL Lock Fail)

The generator did not obtain a frequency

lock by the end of ramp up period.

Press Test button on the power supply. Verify that the

ultrasonic stack will operate in a test condition.

Verify that the stack is operating at proper Frequency

and Power draw.

reduce trigger pressure, force, and/or down speed.

If stack will not operate in test perform stack care and

maintenance.

Follow this link to stack care and maintenance proce

dure.

If Stack will not operate in test condition, remove horn

and re-inspect.

Enable “Advanced Process Settings” to adjust free run

frequency to the “in air” operating frequency that results

from a test.

Enabling a pre-trigger source that allows for full ramp-

up time to elapse still “in air” before contacting the

part should eliminate all “Frequency Overload Fault 1”

occurrences for a properly maintained stack.

If the above steps do not resolve problem, contact

Dukane.

U106

POS Peak Overload Fault Generator ultrasound overload.

Check if one of the stack components is defective.

Check if one of the stack components is loose.

Check if the IQ generator's system frequency settings

are set correctly.

U107

NEG Peak Overload Fault Generator ultrasound overload.

Check if one of the stack components is defective.

Check if one of the stack components is loose.

Check if the IQ generator's system frequency settings

are set correctly.

U108

Average Overload Fault

Generator ultrasound overload.

Reduce the force being applied to the part (on a

pneumatic press) or reduce the weld speed (on a servo

press).

U109

Bad Current Loop Fault

4-20 mA current loop is not connected to

the remote amplitude card, or 4-20 mA

current loop is defective (poor electrical).

Check for proper connection to remote amplitude card.

Check for damage to wiring.

This is a disabling condition for the generator; contact

Dukane.

Alarm Messages

Содержание Infinity 43NSLA


































































Результаты поиска

Содержание Infinity 43NSLA

Отзывы:

Похожие инструкции для Infinity 43NSLA

Бренды по названию

Популярные бренды

Dukane Infinity 43NSLA, Быстрый старт

Результаты поиска

Содержание Infinity 43NSLA

Отзывы:

Похожие инструкции для Infinity 43NSLA

Бренды по названию

Популярные бренды