background image

27

2

1

5

6

3

4

3

1/2

1/2

2

1

3

1

2

4

300

o

2

3

1

A

4

5

4.4 Setting the fork

In the starting position of rest of the trimming mechanism,

when the holder (1) is in contact with the bracket (2), the axis

of the fork (3) must intersect the axis of the shaft (4).

Caution! Danger of injury!

Switch off the main switch! Before starting the

setting operation, wait until the motor stops!

- Shift the shaft (5), until the holder (1) strikes the bracket (2).

- Loosen the screw (6).

- Shift the fork (3) in such a way that its axis intersects the axis

of the shaft (4).

- Tighten the screw (6).

4.5 Setting the moving knife

The moving trimming knife (1) is to be placed in its starting

position at rest with its end at the distance of the measure

„A“= 0.1 to 0.5 mm from the edge of the fixed trimming knife

(2).

The height setting is to be such that its top surface is 1.8 mm

below the top surface of the throat plate.

Caution! Danger of injury!

Switch off the main switch! Before starting the

setting operation, wait until the motor stops!

- Loosen the screws (4 and 5).

- Turn the moving trimming knife (1) in the sense of the arrow

and set it in height. Tighten the screw (5).

- Turn the moving trimming knife (1) into its starting position

in such a way that the measure„A“ = 0.1 to 0.5 mm is

attained. Tighten the screw (4).

4.6 Setting the fixed knife

The fixed trimming knife (1) is to be tensed up by the screw

(2) in such a way that it bears on the moving trimming knife in

the  1/2 of its length. The knives need not to trim untensioned

threads.

Caution! Danger of injury!

Switch off the main switch. Before starting the

setting operation, wait until the motor stops!

- Set the angle of 300

°

 on the handwheel (4).

- Shift by hand the moving knife (3) into the marked position.

- By turning the screw (2), try to set the tensing up of the

fixed trimming knife (1).

- Check the bearing spot of the moving trimming knife (3) on

the fixed trimming knife (1) and give it a correction, if needed.

Содержание 4220-6




































Отзывы: