Contatto
Mod4TP/I
The 4 pairs of Command/Value text boxes allow to send
commands/values to the 4 channels (such as listed in the
the related table).
The four groups of three buttons send Open, Stop and
Close commands respectively (with the related handling of
the long/short pressure). The 4 pairs of b and -, fi-
nally, allow to control the slats executing one step for each
press of the related button.
Technical characteristics
Supply voltage
24V
±
25% SELV
MAX current consumption
95mA @ 24V
Relays contact:
Rating for res. load
1-phase motor
MAX peak current
5A @ 250V~
2.4A @ 250V~ (550VA 0,75HP)
150A (20ms)
Min motor current for travel
time detection
> 100mA
Number of digital inputs
8 for potential free contacts
Nominal input voltage on
digital inputs
24V
Current for each digital input
4mA @ 24V
Operating temperature
-10
¸
+50
°
C
Storage temperature
-30
¸
+85
°
C
Protection degree
IP20
Outline dimensions
90
m
m
58mm
106mm
Power supply 24V=
25% / 95mA
+2
4V
0V
L1
L2
P
1
14
16 17
15
Contatto
DUEMMEGI
MILANO-ITALY
2
3
4
5
6
7
8
13
ADDRESS
MOD4TP/I
Shutter module
C
A1 A2 A3
B1 B2 B3
C1 C2 C3
D1 D2 D3
L
L
L
L
ON
IN
Installation and use restrictions
Standards and regulations
The design and the setting up of electrical systems must be per-
formed according to the relevant standards, guidelines, specifica-
tions and regulations of the relevant country. The installation,
configuration and programming of the devices must be carried out
by trained personnel.
The installation and the wiring of the
Contatto
bus line and the re-
lated devices must be performed according to the recommenda-
tions of the manufacturers (reported on the specific data sheet of
the product) and according to the applicable standards.
All the relevant safety regulations, e.g. accident prevention regula-
tions, law on technical work equipment, must also be observed.
Safety instructions
Protect the unit against moisture, dirt and any kind of damage dur-
ing transport, storage and operation.
Do not operate the unit outside the specified technical data.
Never open the housing. If not otherwise specified, install in closed
housing (e.g. distribution cabinet).
Earth the unit at the terminals provided, if existing, for this purpose.
Do not obstruct cooling of the units.
Setting up
The physical address must be assigned with the specific program-
mer and the setting of parameters (if any) must be performed by
the specific configuration softwares; for more details refer to the
specific data sheet of the product. For the first installation of the
device, generally and unless otherwise specified on the specific
data sheet of the product, proceed according to the following
guidelines:
Check that any voltage supplying the plant has been removed
Assign the address to module (if any)
Install and wire the device according to the schematic dia-
grams on the specific data sheet of the product
Only then switch on the 230Vac supplying the bus power sup-
ply and the other related circuits
Applied standards
The devices belonging to
Contatto
line comply with the essential
requirements of the following directives:
2014/30/UE (EMC)
2014/35/UE (Low Voltage)
2011/65/UE (RoHS)
Correct disposal of the product (waste electrical & electronic
equipment)
(Applicable in the European Union and other Euro-
pean countries with separate collection systems).
This marking on the product, accessories or docu-
mentation indicates that the product and its electron-
ic accessories should not be disposed of with other
household waste at the end of their working life. To
prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate these items from oth-
er types of waste and recycle them responsibly to promote the
sustainable reuse of material resources. Household users should
contact either the retailer where they purchased this product, or
their local government office, for details of where and how they can
take these items for environmentally safe recycling. Business
users should contact their supplier and check the terms and condi-
tions of the purchase contract. Adequate disposal of the decom-
missioned equipment for recycling, treatment and environmentally
compatible disposal contributes in preventing potentially negative
effects on the environment and health and promotes the reuse
and/or recycling of equipment materials. Abusive product disposal
by the user is punishable by law with administrative sanctions.
DUEMMEGI
s.r.l. - Via Longhena, 4 - 20139 MILANO
Tel. 02/57300377 - Fax 02/55213686 –
www.duemmegi.it
Rel.: 1.0 June 2016
Page 6 of 6
