1645 Jill’s Court #108
Bellingham, WA 98226
(360) 788-4200
●
Affordable, Comfortable, Efficient
Infrared Heating Panels
Ducoterra Radiant Heating Panel Installation Manual
1. Introduction
Your new radiant heating panels are designed to heat living and working spaces rapidly and efficiently
by radiant heating. Like the sun, these panels will create a warm environment rapidly for all objects
within line of sight of the panel surface. They are designed to be surface mounted on ceilings or for
installation in a T-bar grid.
2. Installation Layout Guidelines
In a standard 8’ ceiling room, these heating panels will cover approximately 10 times the floor square
footage as panel size (e.g. a 2x4 panel will cover approximately 80 square feet of floor space). They
may be installed at zero clearance to adjoining walls and adjacent panels, but optimal coverage is
obtained by spacing the panels to cover the floor space efficiently.
As maximum panel efficiency is obtained within at 45-degree angle of the panels, spacing panels 2’ off
walls and approximately 4’ from other panels will generally cover a room sufficiently. Panels may need
to be positioned differently depending on specific room configurations, insulation, heating
requirements, and other factors.
3. Environment Insulation Requirements
For proper functionality, the heated space should be insulated appropriately. Optimal panel operation
is achieved if walls and ceilings are insulated according to ASHRAE 189 standards in accordance with
your local climate zone. Heating panel connection box must not be covered with insulation material
after installation to allow for inspection. Heating panel itself has an insulation value of R-5.
4. Wiring Requirements and Guidelines
Heating panel has two 10” 12 AWG leads for connecting to standard #12 power supply with wire nuts
inside the attached connection box. See appropriate wiring diagrams for details (Fig 3).
WARNING: To avoid the risk of electrical shock, personal injury or death, disconnect all
electrical power before installing or performing maintenance on this panel.
The wiring, installation, and electrical hookup of this panel must conform to local and national codes.
Total wattage of heating panels per circuit must not exceed 80% of circuit capacity. Panels should be
installed in conjunction with a line voltage or 24V thermostat. Measure voltage and branch circuit
amperage to determine wattage and panel circuit load.
CAUTION: Wiring procedures and connections shall be in accordance with the national and
local codes having jurisdiction.
WARNING: Panel must NOT be wired to higher voltage than label voltage
1645 Jill’s Court, Suite 108, Bellingham, WA 98226 |
www.ducoterra.com
|
| (360) 788-4200
Affordable, Comfortable, Efficient
Infrared Heating Panels
SolaRay II
Infrared RadiantCeiling Panel
Manufacturer
’
s Suggested Retail Pricing
Effective March1, 2020
Model #
Description
Wattage
MSRP
120AIP2-200
120V Panel 2’x2’
200
$255
240AIP2-200
240V Panel 2’x2’
200
$255
120AIP2-250
120V Panel 2’x2’
250
$275
240AIP2-250
240V Panel 2’x2’
250
$275
120AIP3-300
120V Panel 2’x3’
300
$305
240AIP3-300
240V Panel 2’x3’
300
$305
120AIP3-375
120V Panel 2’x3’
375
$345
240AIP3-375
240V Panel 2’x3’
375
$345
120AIP4-400
120V Panel 2’x4’
400
$385
240AIP4-400
240V Panel 2’x4’
400
$385
120AIP4-500
120V Panel 2’x4’
500
$420
240AIP4-500
240V Panel 2’x4’
500
$420
120AIP4-750
120V Panel 2’x4’
750
$495
240AIP4-750
240V Panel 2’x4’
750
$495
120AIP6-600
120V Panel 2’x6’
600
$520
240AIP6-600
240V Panel 2’x6’
600
$520
120AIP6-750
120V Panel 2’x6’
750
$540
240AIP6-750
240V Panel 2’x6’
750
$540
120AIP6-1000
120V Panel 2’x6’
1000
$625
240AIP6-1000
240V Panel 2’x6’
1000
$625
Note: the above models are also available in 208V or 277V. To order, the model numbers are
208AIPn-www or 277AIPn-www where n=size and www=watts
1645 Jill’s Court, Suite 108, Bellingham, WA 98226 |
www.ducoterra.com
|
| (360) 788-4200
Affordable, Comfortable, Efficient
Infrared Heating Panels
SolaRayII
Infrared RadiantCeilingPanel
Manufacturer
’
s SuggestedRetailPricing
Effective March1, 2020
Model #
Description
Wattage
MSRP
120AIP2-200
120V Panel 2’x2’
200
$255
240AIP2-200
240V Panel 2’x2’
200
$255
120AIP2-250
120V Panel 2’x2’
250
$275
240AIP2-250
240V Panel 2’x2’
250
$275
120AIP3-300
120V Panel 2’x3’
300
$305
240AIP3-300
240V Panel 2’x3’
300
$305
120AIP3-375
120V Panel 2’x3’
375
$345
240AIP3-375
240V Panel 2’x3’
375
$345
120AIP4-400
120V Panel 2’x4’
400
$385
240AIP4-400
240V Panel 2’x4’
400
$385
120AIP4-500
120V Panel 2’x4’
500
$420
240AIP4-500
240V Panel 2’x4’
500
$420
120AIP4-750
120V Panel 2’x4’
750
$495
240AIP4-750
240V Panel 2’x4’
750
$495
120AIP6-600
120V Panel 2’x6’
600
$520
240AIP6-600
240V Panel 2’x6’
600
$520
120AIP6-750
120V Panel 2’x6’
750
$540
240AIP6-750
240V Panel 2’x6’
750
$540
120AIP6-1000
120V Panel 2’x6’
1000
$625
240AIP6-1000
240V Panel 2’x6’
1000
$625
Note: the above models are also available in 208V or 277V. To order, the model numbers are
208AIPn-www or 277AIPn-www where n=size and www=watts
206-880-1558 | 2910 1st Ave S., Seattle, WA 98134 | MightyEnergy.net | [email protected]
1645 Jill’s Court #108
Bellingham, WA 98226
(360) 788-4200
●
Affordable, Comfortable, Efficient
Infrared Heating Panels
Ducoterra Radiant Heating Panel Installation Manual
1. Introduction
Your new radiant heating panels are designed to heat living and working spaces rapidly and efficiently
by radiant heating. Like the sun, these panels will create a warm environment rapidly for all objects
within line of sight of the panel surface. They are designed to be surface mounted on ceilings or for
installation in a T-bar grid.
2. Installation Layout Guidelines
In a standard 8’ ceiling room, these heating panels will cover approximately 10 times the floor square
footage as panel size (e.g. a 2x4 panel will cover approximately 80 square feet of floor space). They
may be installed at zero clearance to adjoining walls and adjacent panels, but optimal coverage is
obtained by spacing the panels to cover the floor space efficiently.
As maximum panel efficiency is obtained within at 45-degree angle of the panels, spacing panels 2’ off
walls and approximately 4’ from other panels will generally cover a room sufficiently. Panels may need
to be positioned differently depending on specific room configurations, insulation, heating
requirements, and other factors.
3. Environment Insulation Requirements
For proper functionality, the heated space should be insulated appropriately. Optimal panel operation
is achieved if walls and ceilings are insulated according to ASHRAE 189 standards in accordance with
your local climate zone. Heating panel connection box must not be covered with insulation material
after installation to allow for inspection. Heating panel itself has an insulation value of R-5.
4. Wiring Requirements and Guidelines
Heating panel has two 10” 12 AWG leads for connecting to standard #12 power supply with wire nuts
inside the attached connection box. See appropriate wiring diagrams for details (Fig 3).
WARNING: To avoid the risk of electrical shock, personal injury or death, disconnect all
electrical power before installing or performing maintenance on this panel.
The wiring, installation, and electrical hookup of this panel must conform to local and national codes.
Total wattage of heating panels per circuit must not exceed 80% of circuit capacity. Panels should be
installed in conjunction with a line voltage or 24V thermostat. Measure voltage and branch circuit
amperage to determine wattage and panel circuit load.
CAUTION: Wiring procedures and connections shall be in accordance with the national and
local codes having jurisdiction.
WARNING: Panel must NOT be wired to higher voltage than label voltage
