background image

22

Instrument panel on handlebar

1) LCD.
2) NEUTRAL LIGHT N (GREEN).
Comes on when in neutral position.
3) HIGH BEAM LIGHT

 (BLUE).

It turns on to indicate that the high beam lights are 
on.
4) ENGINE OIL PRESSURE LIGHT

 (RED).

Comes on when engine oil pressure is too low. It 
must turn on at Key-On, but must turn off a few 
seconds after the engine has started.
It may shortly come on when the engine is hot, 
however, it should go out as the engine revs up.

Important

If this light (4) stays on, stop the engine or it may 

suffer severe damage.

5) FUEL WARNING LIGHT 

 (AMBER YELLOW).

Comes on when fuel is low and there are about 4 
litres of fuel left in the tank.
6) TURN INDICATOR LIGHTS

 (GREEN).

Illuminates and flashes when the turn indicator is in 
operation.

7) “ENGINE/VEHICLE DIAGNOSIS - EOBD” 

LIGHT

 (AMBER YELLOW).

It turns on in the case of “engine” and/or “vehicle” 
errors and in some cases will lock the engine.

1

6

9

7

2

4

5

3

6

8

fig. 4

Содержание Diavel Carbon






















































































































































































































Отзывы: