DTK PRM-13i Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 34

background image

Connector Configuration

13

3.4

J5 - ATX POWER SUPPLY CONNECTOR

J5 is a 2x10 pin male connector. Plug the power connector of the ATX power
supply into the connector.

Fig. 6 ATX Power Supply Connector

3.5

J6 - FLOPPY DRIVE CONTROLLER

This connector supports the floppy drive ribbon cable. After connecting the single
end to the board, connect the two plugs on the other end to the floppy drive.

3.6

J7, J8 –PRIMARY /SECONDARY IDE
CONNECTORS

These connectors support the provided IDE hard disk ribbon cable. After
connecting the single end to the board, connect the two plugs on the other end to
your hard disk or other device.

3.7

J12 – CUSTOMER IR CONNECTOR

J12 is a ten-pin connector for the IrDA/ASKIR/Customer Infrared device. The pin
definition is listed as following:

«
...
17
18
19
20
21
...
»

Содержание PRM-13i



































Отзывы:

Нет отзывов

Похожие инструкции для PRM-13i

Бренд: ECS Страницы: 52

Бренд: Zotac Страницы: 54

ML501MicroBlaze

Бренд: Xilinx Страницы: 46

Бренд: Atmel Страницы: 23

Бренд: Zetex Страницы: 8

Бренд: IEI Technology Страницы: 131

Бренд: CHAINTECH Страницы: 59

Бренд: Linear Technology Страницы: 7

VIOTECH 3100 PLUS - BIOS

Бренд: Biostar Страницы: 41

Бренд: ECS Страницы: 66

STEVAL-LLL002V1

Бренд: STMicroelectronics Страницы: 29

Бренд: ASROCK Страницы: 20

Бренд: Gigabyte Страницы: 39

Бренд: NavSpark Страницы: 18

Бренд: AOpen Страницы: 8

Бренд: SOYO Страницы: 32

Бренд: SOYO Страницы: 94

Бренд: SOYO Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды