DT SWISS RATCHET EXP Скачать руководство пользователя страница 3

Ratchet EXP - Technical Manual

3

1.  GENERAL

1.1  VALIDITY

This manual describes the component specified on the front page and the footer. This manual is 

valid for the design of the product as of 11.01.22. Deviations are possible and all items are subject 

to technical changes.

1.2  SAFETY

The safety instructions are classified as follows:

DANGER

...indicates a hazardous situation that, if not avoided, will result in death or serious injury.

CAUTION

… indicates a hazard with a medium level of risk which, if not avoided, may result in minor or 

moderate injury.

NOTE

… indicates a potentially hazardous situation that may result in damage to property.

1.3  TARGET GROUP

This manual is intended for the user of the component and dealers. This manual offers the 

experienced user the possibility to carry out minor service work himself. If you have any doubts 

about your own abilities, you should definitely contact an expert or a DT Swiss Service Center. 

 

Any warranty claims will lapse if work is not carried out properly.

1.4  LAYOUT

The cover page and the footing provide information about the type of product and manual as well 

as the version of the manual. The DT Swiss contact details can be found on the back. A list of all 

DT Swiss service centers can be found at www.dtswiss.com.
This manual is intended for being printed as an A5 booklet. Only print this manual if electronic 

usage is not possible.

1.5  DT SWISS MANUAL CONCEPT

The DT Swiss manuals are split into the following types of manuals:

• 

User Manual: Information for the end user on how to install and use the component.

• 

Technical Manual: Detailed information for the end user and the dealer on how to maintain 

the component, spare parts and technical data.

Содержание RATCHET EXP
























Отзывы: