DT SWISS RATCHET EXP OS Скачать руководство пользователя страница 4

4

1.6  HOW TO USE THE MANUAL

The steps described in this manual must be carried out in the order they are shown. If steps are ignored or 

executed in a wrong order, the function of the component cannot be guaranteed.

1.7  GENERAL MAINTENANCE INFORMATION

Unless otherwise specified, moving parts, threads, O-rings and seals must be greased before assembly.

CLEANING

For an optimal result of the maintenance work, every component that will be disassembled must be cleaned. 

Only use cleaners which do not damage the components. Especially the cleaning of O-rings and seals 

requires mild cleaners. Observe the instructions for use of the respective cleaner.

DT Swiss recommends the following cleaners:

•  Motorex Rex
•  Motorex Swissclean
•  Motorex OPAL 2400, 3000 OPAL, OPAL 5000

Use soap water or similar mild cleaners for external cleaning.

TOOLS

To ensure a damage-free mounting and dismounting of the components, only use the tools which are 

mentioned in this manual. Special tools are indicated at the beginning of a chapter in the table "Required 

Tools". 

The use of different tools is at the discretion of the user. If components are damaged by the usage of differing 

tools, the user is liable.

DT Swiss special tools are precision tools. Damage-free mounting and dismounting of the components can 

only be ensured if the tools are working properly and if the condition of the tools are perfect. Always keep the 

tools in their original packaging or adequate devices to prevent damage.

1.8  ENVIRONMENTAL PROTECTION

The statutory regulations shall apply. Whenever possible, avoid creating waste. Waste, especially carbon, 

lubricants, cleaners and any other fluids must be disposed in an environmentally compatible manner.

 

Only print this manual if electronic usage is not possible.

1.9  EXCLUSION OF LIABILITY

The activities listed in this manual may only be carried out by persons with sufficient specialist knowledge. 

The user is liable for any damage or consequential damage caused by wrongly maintained or installed 

components. If you have doubts, please contact your region's DT Swiss pro level service center.

1.10 WARRANTY

Warranty conditions, see www.dtswiss.com

Содержание RATCHET EXP OS





















Отзывы: