manualshive.com logo in svg

DT SWISS D 232, Техническое руководство

Поделиться
Скачать
DT SWISS D 232 Скачать руководство пользователя страница 14

14

5.  TROUBLE SHOOTING

Issue

Reason

Solution

seat post does not compress 

or extend properly

dirty / too little grease

small service 

details, see 

6 on page 

17

O-ring (“2. Overview” on 

page 

6

 / No. 13) crushed / 

defective

disassemble the seat post 

completely, clean all parts. 

 

replace 

guiding kit

. 

details, see 

7 on page 

24.

wiper seal of lock nut damaged

disassemble the seat post 

completely, clean all parts.

 

replace 

slider tube nut kit

. 

details, see 

7 on page 

24.

release piston jammed

disassemble the seat post 

completely, clean all parts.

 

replace 

latch system kit

. 

details, see 

7 on page 

24.

seat post blocked / does not 

release

cable tension too low

increase tension of the cable

cable torn

replace cable

cable unhooked from the 

quickconnector

dismount the seat post and attach 

the cable

quickconnector damaged

replace 

quickconnector kit

. 

details, see 

7 on page 

24.

lower seat tube cover damaged install new 

seat tube cover

.  

details, see 

7 on page 

24.

connection of quickconnector 

and actuating spoke loose

clamp actuating spoke to 

quickconnector.

 

details, see 

“Mounting the 

Quickconnector” on page 34

.

actuating spoke defective

replace the 

actuating spoke

. 

details, see 

“Mounting the 

Quickconnector” on page 34

.

release piston jammed

disassemble the seat post 

completely, clean all parts.

 

replace 

latch system kit

. 

details, see 

7 on page 

24.

O-ring (“2. Overview” on 

page 

6

 / No. 13) crushed / 

defective

disassemble the seat post 

completely, clean all parts.

 

replace 

guiding kit

. 

details, see 

7 on page 

24.

Содержание D 232










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды