DT SWISS D 232 Скачать руководство пользователя страница 13

Страница: 13 / 41

D 232 - Technical Manual V2020.05

4. SERVICE AND CARE

4.1 SAFETY

DANGER

RISK OF INJURY DUE TO WRONG MAINTENANCE OF THE SEAT POST!

Incorrect maintenance or assembly of the seat post can lead to incorrect function!

•

Maintenance and assembly may only be done by a skilled professional.

•

In case of any doubt, contact a DT Swiss service center.

•

Only use original spare parts.

4.2 SERVICE INTERVALS

If service intervals are not respected, any warranty claims can be denied.

Task

Interval

Full service

see

“7. Full service” on page

Annually or after 200 operating hours

Small service

see

“6. Small service” on page

50 operating hours

more frequently in case of extreme operating

conditions.

Check the seat post for damage and cracks.

If there is any damage, contact the DT Swiss Service

Center.

Before and after every ride

and after a crash

Check the fastening is correct / check tightening

torques

Before each ride

Check the functionality

Before each ride

Seat post care (see below)

After each ride

4.3 CARE

The following care and cleaning instructions must be observed:

•

Clean the seat post with a damp cloth after each ride. Remove dirt accumulations in the area

of the wiper seal.

•

Never use aggressive cleaners that damage the wiper seal.

•

Never use high pressure cleaners. Water and dirt can get into the seat post and damage it!

•

Remove all visible, dried dirt from the area of the wiper seal. This will prevent dirt from getting

into the seat post.

•

It is not necessary to grease the seat post in the area of the wiper seal.

Содержание D 232










































Результаты поиска

Содержание D 232

Отзывы:

Бренды по названию

Популярные бренды

DT SWISS D 232, Техническое руководство

Результаты поиска

Содержание D 232

Отзывы:

Бренды по названию

Популярные бренды