DSC Power608 Скачать руководство пользователя страница 29

Страница: 29 / 52

P r o g r a m D e s c r i p t i o n s :

5 . 2 2 K e y p a d B l a n k i n g

To disable the keypad lockout option, program the Number of
Invalid Codes Before Lockout as [000].

NOTE: If Keypad Lockout is active, the panel CANNOT be
armed / disarmed with a keyswitch.

Keypad Lockout Options . . . . . . . . . . . . . . . . . Section [012]

5.22 Keypad Blanking

If the

Blank Keypad When Not in Use

option is enabled, the

panel will turn off all lights and LCDs on the keypads when no
keys are pressed for 30 seconds. The keys, however, will
remain backlit.
The panel will turn the lights and LCDs back on if entry delay
begins or an audible alarm occurs. The lights and LCDs will
also come on if a key is pressed or, if a valid access code is
entered when the

Code Required to Restore Blanking

option is enabled.

NOTE:If using a PC5132 v3.0 or greater, and wireless keys, do
not enable the Code Required to Restore Blanking option, as
the keys will not function correctly.

If the

Power Save Mode

option is enabled the panel will blank

all keypad lights including backlighting when AC power fails,
in order to conserve the backup battery.

Blank Keypad when not in use. . . . . . . . . .  Section [016]: [3]
Code Required to Restore Blanking. . . . . .  Section [016]: [4]
Power Save Mode  . . . . . . . . . . . . . . . . . . .  Section [016]: [6]

5.23 Keypad Backlighting

The keys of all the keypads can be backlit to provide easy
viewing in dim lighting conditions. If the

Keypad Backlighting

option is enabled the keys will be illuminated.

Keypad Backlighting Option . . . . . . . . . . . Section [016]: [5]

5.24 Loop Response

The normal loop response time for all zones is under 400 milli-
seconds.
Zones 1-6 on the control board, however, can be programmed
for a fast loop response (under 40ms).

Zones 1-6 are Fast Loop Response . . . . . Section [030]: [1-6]

5.25 Keypad Tampers

If the

Keypad Tampers Enable

option is selected, the panel

will display and transmit a

General System Tamper

reporting

code if any keypad is removed from the wall. When the key-
pad tamper is restored, the panel will transmit the

General

System Tamper Restoral

reporting code. All keypads should

be properly installed and secured before enabling this option.
If the

All System Tampers Require Installer Reset

option is

enabled, any system tampers must be reset by entering
[*][8][Installer’s Code] before the system can be armed. Auto-
Arming and Keyswitch arming will also be prevented in the
presence of any system tamper.
The

Auto Arm Cancellation

code is not transmitted when a

reset is required because a user has not cancelled the auto
arming sequence.

Keypad Tamper Enable . . . . . . . . . . . . . . . Section [016]: [8]
General System Tamper and Tamper
Restoral Reporting Codes . . . . . . . . . . . . . . . . Section [338]

System Tampers Req. Installer Reset . . . . .Section [701]: [4]

NOTE: After enabling keypad tampers, it is recommended to
tamper and restore all keypads to ensure proper functioning.

5.26 Additional System Modules

The following modules are programmed through the Module
Programming sections [801]-[804]: the PC5400 Printer mod-
ule, the PC59XX Audio Interface module, the Links2X50 Long-
Range Radio interface and the PC5132 Wireless Receiver and
all of its devices. For instructions on the installation and pro-
gramming of these additional modules and devices, please
see their respective installation and programming manuals.

PC5400 Programming . . . . . . . . . . . . . . . . . . . . Section [801]
PC59XX Programming . . . . . . . . . . . . . . . . . . . . Section [802]
LINKS2X50 Programming . . . . . . . . . . . . . . . . . Section [803]
PC5132 Programming . . . . . . . . . . . . . . . . . . . . Section [804]

5.27 Engineer's Reset

If the

Engineer’s Reset

option is enabled, if the panel has

gone into alarm during the previous armed period, or if a 24
Hour zone has gone into alarm, the system will not be ready to
arm (Ready Light OFF) until:

•

Installer’s Programming is entered

•

Engineer's Reset is performed via Downloading software.

NOTE:This feature applies to Tampers and Faults in both
armed and disarmed states. This does not apply to Module
Tampers, System Supervisories, Zone Expander or PGM2
alarms.

Engineer’s Reset . . . . . . . . . . . . . . . . . . . . .Section [018]: [2]

5.28 Clock Adjust

In order to compensate for timing inaccuracies, the panel may
be programmed to add or subtract seconds during the last
minute of each day using the

Clock Adjust

programming sec-

tion. Valid entries are 01 - 99. The default setting is 60 sec-
onds. To determine the value to be programmed in this
section, monitor the amount of time lost or gained by the panel
over a period of time. Then, calculate the average amount of
time per day that the panel gains or loses. If the clock’s timing
is off, it may be corrected with this setting.

Example #1:

The clock loses an average of 9 seconds per

day.

Solution:

Program the panel to adjust the clock by 51

seconds (instead of the default 60 seconds) for the last minute
of each day in section [700]. This will speed up the panel’s
clock by 9 seconds, correcting the problem.

Example #2:

The clock gains an average of 11 seconds per

day.

Solution:

Program the panel to adjust the clock by 71

seconds (instead of the default 60 seconds) for the last minute
of each day in section [700]. This will slow down the panel’s
clock by 11 seconds, correcting the problem.

NOTE: If the auto-arm time is set for 23:59, any change to the
Clock Adjust option will directly affect the auto-arm pre-alert
time.

Clock Adjust. . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [700]

5.29 Timebase

In cases of unstable AC power input you can use the internal
crystal to keep a more accurate timebase by enabling the

Timebase is Internal Crystal

option.